Technical Data - EINHELL BG-EC 620 T Mode D'emploi D'origine

Anleitung_BG_EC_620_T_SPK7__ 10.07.12 13:25 Seite 19
When the equipment is in operation keep other
n
persons and animals away from the danger zone.
The equipment is not protected from electric
n
shock through contact with high-voltage cables.
Keep a minimum distance of 10 m from live
cables. Electric shock can cause fatal injury.
When working on slopes always stand to the
n
upper or left or right side of the branch you wish to
cut.
Hold the equipment as close as possible to your
n
body. This will help you to keep your balance.
Cutting techniques
When removing branches, hold the equipment at
n
an angle of max. 60° to the horizontal to avoid
being hit by a falling branch.
Start with the bottom branches on the tree. This
n
will make it easier for the cut branches to drop.
After completing a cut, the weight of the saw will
n
abruptly increase for the operator as the saw is no
longer supported by the branch. This can result in
you losing control over the saw.
Remove the saw from the cut only with the saw
n
chain still running. This will prevent the saw from
getting jammed.
Never cut with the tip of the saw.
n
Never cut into the bulging branch collar. This will
n
prevent the tree from healing.
Sawing off smaller branches (Fig. 17):
Place the contact surface of the saw onto the branch.
This will prevent the saw from making jerky
movements when you begin a cut. Exerting slight
pressure, guide the saw from the top to the bottom
through the branch.
Sawing off larger and longer branches (Fig. 18):
Carry out a relief cut when working on larger
branches.
Start by sawing through 1/3 of the branch diameter
(a) from the bottom to the top with the top side of the
cutter rail. Then saw towards the first cut (b) from the
top to the bottom with the bottom side of the cutter
rail.
Saw off longer branches in several steps to keep
control over the impact location.
Kick-back!
The term "kickback" describes what happens when
the running chainsaw suddenly kicks upward and
backward. Usually, this is caused by contact between
the tip of the cutter rail and the workpiece or the saw
chain becoming trapped.
In the event of kickback, large forces occur suddenly
and violently. As a result, the chainsaw usually reacts
uncontrollably. This can often result in very serious
injuries to the worker or persons in the vicinity. The
risk of kickback is at its greatest when the saw is
positioned for a cut in the region of the tip of the cutter
rail, as the leverage effect is greatest there. It is
therefore safest to position the saw as flat as possible.
Important!
Make sure that the chain tension is always
n
correctly adjusted.
Only use a chainsaw if it is in perfect working
n
order.
Only work with a saw chain that has been
n
properly sharpened in accordance with the
instructions.
Never cut with the upper edge or the tip of the
n
cutter rail.
Always hold the chainsaw firmly with both hands.
n
Cutting wood which is under tension
Special care is required when cutting wood which is
under tension. Wood which is under tension from
which it is released by cutting may in some cases
react completely unpredictably and uncontrollably. In
the worst case this could result in extremely severe or
even fatal injuries. This type of work must only be
performed by persons who have been specially
trained.

7. Technical data

Mains voltage:
Power rating:
Cutter rail length:
Cutting length, max.:
Cutting speed at rated rpm:
Oil tank capacity:
Weight with cutter rail and chain:
Chain: Oregon 90JG033X, 91P033X
Cutter rail:
080NDEA041, 084LNEA041
Protection class:
GB
230 V ~ 50 Hz
600 W
200 mm
180 mm
13 m/s
110 ml
4.6 kg
Oregon 080NATAA041,
II / ®
19