Silverline DIY Série Mode D'emploi page 9

324178
Product Familiarisation
1 Silencer
2 Pressure Switch Box
3 Compressed Air Outlet Gauge
4 Pressure Regulator
5 Compressed Air Outlet Gauge
6 Unloading Pipe
7 Tank Drain Screw
8 Wheels
9 Air Pipe
10 Tank
11 Fan Cover
12 Rubber Foot
13 Bolt (Rubber Foot)
14 Crankcase Breather
15 Wheel Bolts x 2
16 Air Filter
17 Oil Bottle
18 Crankcase Breather Hole
19 Oil Level Monitor
20 Threaded Air Intake Port
21 ON/OFF Switch
22 Pressure Release Valve
23 Quick Connector
24 Quick Connector
25 Front Transport Handle
26 Rear Transport Handle
Intended Use
Mains-powered, oil-lubricated air compressor with large-capacity compressed air tank. Supplies
power to a wide variety of air tools, including spray guns and impact wrenches.
Unpacking Your Tool
WARNING: This device is very heavy and should NOT be unpacked and handled by a single
person .
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features
and functions
• Ensure that all parts of the tool are present and in good condition . If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
DIY 2hp Air Compressor 1500W
Before Use
Wheel installation
1. Place the air compressor unit on a secure, flat surface ready for assembly, and locate the Wheels
(8) and Wheel Bolts (15)
2. Carefully place the air compressor unit on its side to gain access to the wheel mounting holes
(Fig IV)
3. Slide the Wheel Bolt threaded end first through the centre of the Wheel and then through the
wheel mounting hole
4 . Fasten using the corresponding nut
5 . Repeat steps 1-4 for the other side
Rubber foot installation
1. Place the air compressor unit on a secure, flat surface to reveal the foot mounting hole (Image A).
Locate the Rubber Foot (12) and Bolts (Rubber Foot) (13)
2. Slide the supplied fixing bolt through the bottom of the Rubber Foot (Image B), then through the
foot mounting hole (Fig V), and fasten using the corresponding washer and nut
Air filter installation
1 . The Threaded Air Intake Port (20) is located on the side of the cylinder head (Image D)
2. Screw the Air Filter (16) into the Threaded Air Intake Port
Filling with motor oil & Crankcase Breather
installation
WARNING: This air compressor is supplied without oil. DO NOT attempt to start the motor before
you have filled the motor with the appropriate type and amount of oil.
WARNING: Only use an oil type listed in the 'Specification' . High viscosity oil could create blockages
due to improper circulation during cold starts. A low viscosity oil will be unable to lubricate the
compressor sufficiently.
Note: Change the lubricating oil and clean the crankcase after the first 10 working hours.
Note: Always place the air compressor on a level surface before filling motor oil or checking oil
levels .
1. Position the air compressor on a secure, flat surface
2 . Remove the shipping plug from the Crankcase Breather Hole (18), and store in a safe place . The
Crankcase Breather Hole is now accessible
Note: This air compressor features and external Oil Level Monitor (19) (Image C) for easy monitoring
of oil levels .
3. Fill with suitable motor oil (Fig III) to the centre of the red 'FULL' mark on the Oil Level Monitor
4. Screw the Crankcase Breather (14) into the Crankcase Breather Hole
Fitting the quick connector
Note: This tool is supplied with two 3-in-1 air line quick connectors:
1. Apply PTFE tape (not included) to the screw threads of the Quick Connectors (23 & 24) (Image F).
This will help maintain an air-tight seal
Note: Apply PTFE tape tightly and in a clockwise direction, so it does not come off when the thread
is screwed into the tool.
2 . Remove the protective plug from the air outlets attached to the Pressure Regulator (4)
3. Using a spanner (not included), screw the Quick Connectors one at a time into the air outlets
4 . Connect to air line, pressurise carefully and carry out a leak check (e .g . by spraying small
amounts of soapy water on to the outside of the connectors)
• Air lines fitted with matching male quick connectors will now be a push-fit to the
tool
Check valves & fasteners
Note: Always check the operation of the Pressure Release Valve (22) before use; its function is
imperative to the safe use of this air compressor .
• Ensure all valves and fasteners are correctly tightened/seated for operation before
each use
silverlinetools.com
9