Maintenance; General; Daily Cleaning; Cleaning The Top Hood - Hatco Thermo-Finisher TFWM Série Manuel D'installation Et D'utilisation

MAINTENANCE

General

Hatco Thermo-Finisher
®
designed for maximum durability and performance, with
minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn power switch OFF, unplug power cord/turn off
power at circuit breaker, and allow unit to cool before
performing any maintenance or cleaning.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not "jet-proof" construction. Do not use
jet-clean spray to clean this unit.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged
power cord. The cord must be replaced by Hatco, an
Authorized Hatco Service Agent, or a person with
similar qualifications.
• This unit must be serviced by a licensed electrician.
Service must conform to all local electrical codes.
Service by unqualified personnel will void the unit
warranty and may lead to electric shock or burn, as
well as damage to the unit and/or its surroundings.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
NOTICE
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
Use non-abrasive cleaners on glass and metal surfaces.
Abrasive cleaners could scratch the finish of the unit,
marring its appearance and making it susceptible to soil
accumulation.

Daily Cleaning

For sanitary operation as well as to preserve the condition of
the unit and maintain performance, it is recommended that the
unit be cleaned daily.
1. Move the POWER ON/OFF (I/O) switch to the OFF (O)
position and allow the unit to cool completely.
2. Remove and wash the adjustable shelves and bay dividers.
3. Wipe the exterior and interior of the unit with a clean,
sanitized cloth.
• Hard to reach areas may be cleaned using a small
brush and mild soap.
• Stubborn stains on the stainless steel may be removed
with a good stainless steel cleaner or a non-abrasive
cleaner.
4. For TFWM42-3939 and TFWM36-3939 models:
a. Carefully scrape and wipe off debris from the glass
surface above the lower ribbon heating elements.
b. Clean the glass surface using a standard ceramic glass
cleaner.
wall mounted food finishers are

Cleaning the Top Hood

Check the condition of the top hood weekly and clean if
necessary. To clean the top hood:
1. Move the POWER ON/OFF (I/O) switch to the OFF (O)
position and allow the unit to cool completely.
2. Unplug the power cord/turn off the power at circuit breaker.
• Units must cool completely before unplugging power
cord/turning off the power at circuit breaker. Failure to
allow unit to cool completely will trip the high limit switch.
Contact Service if the indicator light above the POWER
ON/OFF (I/O) switch is illuminated.
3. Remove the four screws that secure the top hood to the top
of the unit. Set aside the screws and hood for reassembly.
4. Clean inside the hood with a clean, sanitized cloth.
CAUTION! Keep fingers and/or other small objects
away from fan guards.
5. Remove the air filter.
6. Clean the exposed top flanges as required. WARNING!
Take extreme care not to drip cleaning solution in the
area of the fans and/or filter–doing so may create a
risk of fire and/or electric shock. Wipe all surfaces dry.
7. Inspect the removed air filter and replace with a new filter,
if necessary. NOTICE: Never operate the unit without
the filter installed.
8. Install the air filter back into fan channel.
9. Position the top hood over the air filter channel.
10. Align the four top hood holes with the holes on the top of
the unit.
11. Replace the four screws and tighten securely.
Air
Filter
Fan
Channel
Cleaning the Top Hood
12
English
Top
Cover
Screws
Form No. TFWMM-0817