Updating Firmware; Maintenance; General - Hatco IRNG Série Manuel D'installation Et D'utilisation

English

Updating Firmware

Use the following procedure to upload firmware updates to the
Induction Range from an external USB drive. This procedure
can be done in both operation modes.
NOTE: For the latest firmware updates, cooking tips, and
more, go to the Hatco Induction Range website:
www.hatcocorp.com/rapide_cuisine
1. Push the Control Knob to start the
Induction Range.
2. Touch the Button on the control
panel to toggle through the screens
on the Control Display to the
Settings Screen.
3. Turn the Control Knob clockwise until FIRMWARE is
highlighted in red, then push the Control Knob to select
FIRMWARE.
• A password screen will appear.
• To enter the 3-digit password
"248", turn the Control Knob to
the first number, then press the
Control Knob to select and move
to the next number.
• The Firmware screen will appear.

General

Hatco Induction Ranges are designed for maximum
durability and performance with minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and
allow unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Do not allow
liquids to spill into unit. Unit is not waterproof. Do not
operate if unit has been submerged or saturated with water.
• Do not steam clean or use excessive water on the unit.
• This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. Cord must be replaced by an Authorized Hatco
Service Agent or a person with similar qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
Form No. IRNGM-1120
4. Depending on the type of update, turn the Control Knob to
5. Insert the USB drive into the USB
Settings
Firmware
Modes
6. Turn the Control Knob to highlight UPDATE, then push the
Errors
Settings—Standard
NOTE: If an error message appears
ELECTRIC SHOCK HAZARD: Use only Genuine Hatco
Replacement Parts when service is required. Failure to use
Genuine Hatco Replacement Parts will void all warranties
and may subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to operate
safely in the environments in which they are used. Some
after-market or generic replacement parts do not have the
characteristics that will allow them to operate safely in
Hatco equipment.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
Use only wipes, pads, and cleaners designed specifically
for cleaning ceramic glass surfaces.
Wipe up all spills and splashes immediately. Make sure unit
is dry before using. Do not allow liquid to run into air inlet
filter on bottom of unit.
15
highlight either USER BRD or MAIN BRD, then push the
Control Knob to select.
• The Firmware Update screen will appear.
port.
• The USB port is on the right side
of countertop units and on the
under-side of the control panel
on built-in units.
Control Knob to start the update.
• A screen will appear to indicate the update is in progress.
• When the update is complete, the Welcome screen will
appear for a few seconds showing the new firmware
version, and the unit will shut down.
indicating that the update has
failed, perform the "Resetting
the Software" procedure in
this section. Then, perform the
"Updating Firmware" procedure
again using a new USB drive.
WARNING
CAUTION
OPERATION
HOLD Menu+Timer
FOR 10 SEC
Error F69

MAINTENANCE

continued...