Noise And Vibration Indications; Proper And Improper Use Of The Machine; General Warnings And Behavioural Norms - Rivacold FS Série Mode D'emploi Et D'entretien

Masquer les pouces Voir aussi pour FS Série:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

3.6. Noise and Vibration Indications

3.6.1. Noise
B
FS were designed and manufactured to reduce the noise emitted during normal functioning to a minimum.
LOCKSYSTEM
The level of mass acoustic pressure A generated by B
during functioning is less than 70 dB (A).
3.6.2. Vibrations
In use conditions in compliance with the instructions supplied by the manufacturer in this handbook, the vibrations were not such to
create dangerous situations.
The operator however, if vibrations occur, should immediately stop the machine and signal the phenomenon to the manufacturer's
support service.

3.7. Proper and Improper Use of the Machine

The machine was designed and built exclusively for industrial and commercial refrigeration in a fixed location. It is exclusively
designed to be installed on a vertical wall.
The
can only use the refrigerant for which it was designed (typically R404A). Check the machine label in order to identify the
MACHINE
refrigerant gas for which the machine was designed and built.
The machine was designed and built to operate in environments where there is no danger of explosion and by itself cannot generate a
potentially explosive atmosphere.
The machine must be adequately protected from atmospheric agents.
It is good practice to keep powder extinguishers near the machine. To prevent the possibility of a fire the machine must be kept clean
of plastic pieces, oils, solvents, paper, and rags.
Use of the machine for operations other than its intended use could cause harm to people or the machine itself and are thus
considered improper uses for which the Manufacturer is not responsible.
WARNING:

3.8. General Warnings and Behavioural Norms

To avoid any risky conditions to people or damage to the machine, we recommend you scrupulously follow the general warnings and
behavioural norms reported here.
DANGER:
The operators responsible for machine management must be adequately trained to use it at its best and without risk and must
operate in a comfortable environment that guarantees the best safety and hygiene conditions possible.
DANGER:
Before using the machine, ensure that any dangerous conditions to safety are adequately eliminated and that there are no
operators present in the danger zones near the machine.
Before using the machine, ensure all the guards are in place and that all safety devices are present and efficient.
Warn supervisors of any functioning irregularities in the machine or any problems relating to the integrity of the machine
protections.
Carefully read the machine labels. Do not cover them for any reason and replace them immediately if damaged.
Do not rest liquid containers on the machine.
Consult this handbook on the safety specifications in force and the specific
however, the staff responsible for the machine must wear suitable clothing, by avoiding or paying due attention to:
loose clothing,
wide sleeves,
ties or hanging scarves,
necklaces, bracelets and rings.
Staff responsible for maintenance of the machine must be aware of all the procedures reported in Chapter 6 – Maintenance and
Demolition and be adequately prepared technically to correctly interpret the instructions and diagrams in this handbook and to
intervene on the machine.
The area where the maintenance operations take place must always be clean, dry and with suitable equipment always available
and efficient.
The work area must never be occupied in such a manner to interfere with the free movement of the operator. In case of
emergency, immediate access to the machine must be guaranteed for responsible staff.
In the aforementioned area, access to people who are not directly responsible for machine functioning is forbidden, to avoid
danger due to distraction or negligence during machine intervention.
If intervention has to be conducted near the electrical components, work with dry hands and use dielectric gloves (working on
electrical components with wet hands leads to almost certain danger of electrical shock).
DANGER:
LOCKSYSTEM
for a different destination of use, prior consultation with the Manufacturer's Technical Office is
essential.
the manufacturer declines all responsibility for any damage to property and/or persons deriving from
improper interventions conducted by unqualified, untrained or unauthorised staff.
prevent the machine being used by unauthorised staff or untrained staff without supervision: in fact, before
starting work, each operator must be perfectly aware of the position and functioning of all the controls and
features of the machine. Furthermore, the operator must have read this handbook
you should ensure that before starting any type of machine intervention or corresponding to its components
or accessory equipment to section power; if this is not possible, it is necessary to take measures to allow you
to operate on the machine in safe conditions.
FS and measured, following the criteria set by the norms in force,
to implement for personal safety; in particular,
IPD
UK
.
ENTIRELY
FS Pag. 44 Rev 00 02/12

Publicité

Table des Matières
loading

Table des Matières