Safety And Technical Data; Safety General Information; Protection Device And Solutions; Residual Risk Warnings - Rivacold FS Série Mode D'emploi Et D'entretien

SIMBOL
"ON/OFF" key: This is used as a manual on-off control, to confirm a parameter value and it also allows you to return
to the previous menu. To switch the machine on or off, hold this key down for more than 5 seconds.
"DOWN" key: This is used to command the lights manually (if held down for 1 second); it also decreases the value of
the parameter being displayed and scrolls back through the menu list.
3 . S a f e t y a n
3 . S a f e t y a n

3.1. Safety General Information

3.1.1. Engineering Criteria
For the machine design, the principles and concepts introduced in the relevant paragraphs of the norms indicated in Table 3 were
implemented.
Table 3 – Main norms used in the machine design.
NORM
12100-1: 2009
UNI EN ISO
12100-2: 2009
UNI EN ISO
14121-1: 2007
UNI EN ISO
13857: 2008
UNI EN ISO
953: 2009
UNI EN
60204-1: 2006
CEI EN
60335-1: 2008
CEI EN
The compliance of the paragraphs to the aforementioned norms has enabled risks to be eliminated or reduced as much as possible,
both during normal functioning and during regulation and maintenance operations, for the entire lifecycle of the machine.
The components used were carefully chosen among those available on the market and the materials composing the machine (and the
machine accessory tools) present no risks to personal health and safety. All the parts provided by third parties are CE marked (when
planned) and comply with the relevant reference directives. All the details were closely controlled in compliance with the qualitative
standards prescribed by the laws in force.
For the machine, the warning and protection measures were also implemented that are necessary to confront residual risks (see
Paragraph 3.3 – Residual Risk Warnings on this).
3.2. Protection Devices and Solutions
3.2.1. Passive Safety Devices
The following construction solutions and devices were adopted for the machine
Fixed guards on all sides of the machine which enclose the entire body of the condensing unit and the evaporator.
Fixed guards in metal or plastic mesh near the moving parts.
Safety signs near the machine protections.
3.2.2. Active Safety Devices
The machine includes active safety devices as described below.
Safety pressure switch on the compressor
Security valve (when provided)

3.3. Residual Risk Warnings

To avoid all dangerous conditions for people or damage to the machine caused by residual risks, i.e. those risks that persist despite all
the devices implemented, or potential risks that are not obvious, the manufacturer recommends the operators, maintenance staff and
all staff working on the machine scrupulously follow the warnings on the following pages.
ATTENTION
3.3.1. Lifting and Transportation
3.3.1.1. Residual Risks During Lifting and Transport Phases
During the lifting and transport phases, risks are present related to:
operations on the machine by staff that is unqualified, untrained, uninformed or not correctly equipped.
d T e c h n i c a l D
d T e c h n i c a l D
Safety of the machinery - Key concepts, general engineering principles - Part 1: Base terminology,
methodology
Safety of the machinery - Key concepts, general engineering principles - Part 2: Technical principles
Safety of the machinery - Evaluation of the risks - Part 1: principles
Safety of the machinery - Safety distances to prevent upper and lower limbs from reaching dangerous
areas
Safety of the machinery - Guards - General requisites for the engineering and the construction of the fixed
and mobile guards
Machinery safety – Electrical equipment on the machine - Part 1: General rules:
Safety of the electrical equipment intended for domestic use and other similar equipment - Part 1:
General norms
:
always comply with the notifications and instructions on the plates applied to the machine and operate
exclusively based on the instructions provided in this handbook (for example those reported in Paragraph
3.8 – General Warnings and Behaviour Norms).
DESCRIPTION
a t a
a t a
TITLE
UK
FS Pag. 40 Rev 00 02/12