Transportation And Storage - Ryobi RCS36X3550HI Traduction Des Instructions Originales

Masquer les pouces Voir aussi pour RCS36X3550HI:

page de 317

/ 317
Matières
Table des Matières
Signets

Table des Matières

Les langues disponibles

3. The saw chain should face in the direction of chain

rotation. If they face backwards, turn the loop over.

4. Place the chain drive links into the bar groove.

5. Position the chain so there is a loop at the back of the

bar.

6. Hold the chain in position on the bar and place the loop

around the drive sprocket. Lower the bar so that the

bolt goes through the hole in the attached chain tension

assembly. You may need to rotate this assembly so the

bolt and hole align. You may rotate this assembly again

to apply some tension to the chain which will help keep

it in place.

7. Replace the sprocket cover and turn the chain tensioner

knob until nearly tight, turn the chain tension adjustment

ring until the saw chain is properly tensioned. The guide

bar must then be pushed upwards, check chain tension

again, do not tension the chain too tight.

8. After the chain is well-tensioned, tighten the knob again.

ADJUSTING THE CHAIN TENSION

See page 265. See page 275.

1. Loosen the chain tensioner knob slightly by turning it

counterclockwise.

2. To increase the chain tension, turn the chain tensioner

adjustment ring clockwise and check the chain tension

frequently. To reduce the chain tension, turn the chain

tensioner adjustment ring counterclockwise and check

the chain tension frequently.

3. The chain tension is correct when the gap between the

cutter in the chain and the bar is between 3 mm - 4

mm. Pull the chain in the middle of the lower side of the

bar downwards (away from the bar) and measure the

distance between the bar and the chain cutters.

4. Tighten the chain tensioner knob by turning it clockwise.

OPERATION

ADDING CHAIN LUBRICATING OIL

See page 265.

WARNING

Never work without chain lubricant. If the saw chain is

running without lubricant, guide bar and saw chain can

be damaged. It is therefore essential to check the oil

level in the oil level gauge frequently and every time

before starting to use the chain saw.

1. Clear surface around the oil cap to prevent

contamination.

2. Unscrew and remove the cap from the oil tank.

3. Pour the oil into the oil tank and monitor the oil level

gauge. Ensure that no dirt enters the oil tank while

filling.

4. Put the oil cap back on and tighten it up. Wipe away

any spillage.

5. One full oil tank will enable you to use the saw for 20-

40 min.

Recommended chain lubricating oil

The manufacturer recommends you use only RYOBI

■

chainsaw lubricating oil. (Available from your authorised

RYOBI service centre)

INSTALLING BATTERY PACK

See page 265.

1. Place the battery pack in the chain saw. Align raised

ribs on battery pack with grooves in the chain saw's

battery port.

2. Make sure the latch on bottom of the battery pack

snaps in place and that battery pack is fully seated and

secure in the chain saw before beginning operation.

HOLDING THE CHAIN SAW

See page 265.

Always hold the chain saw with your right hand at the rear

handle and your left hand at the front handle. Grip both

handles with the thumbs and fingers encircling the handles.

Ensure that your left hand is holding the front handle so that

your thumb is underneath.

STARTING THE CHAIN SAW

See page 265.

1. Before starting for operation, you should install the

battery pack in the machine, and make sure chain

brake is in run position by pulling chain brake lever /

hand guard toward the front handle.

2. To start the machine: pull the trigger release, and then

press the throttle trigger.

CHECKING AND OPERATING CHAIN BRAKE

1. Engage the chain brake by rotating your left hand

around the front handle. Allow the back of your hand to

push the chain brake lever/hand guard toward the bar

while the chain is rotating rapidly. Be sure to maintain

both hands on the saw handles at all times.

2. Reset the chain brake back into the Run position by

grasping the top of the chain brake lever / hand guard

and pulling toward the front handle until you hear a

click.

WARNING

If the chain brake does not stop the chain immediately, or

if the chain brake will not stay in the run position without

assistance, take the saw to an authorised service centre

for repair prior to use.