NovoPress AXI102 Manuel D'utilisation page 22

Masquer les pouces Voir aussi pour AXI102:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 29
AXI102 / AAP102
reasons, the positive control is only activated after a minimum force has been attained. Until this force
is achieved, the expansion process can be interrupted at any time by releasing the start button (1).
EN
The device then automatically returns to its initial position.
Pos : 29 /RVT/Kurz bes chr eibung/Entriegel ungsknopf/AXI102 @ 0\mod_1382426033219_18.doc x @ 1414 @ 3 @ 1
7.1.2 Release button (5) (Fig. 1)
The release button (5) is used to return the tool to its initial position before the expansion process has
been completed. In order to do this, press the release button (5) until the expander head (7) has
moved back completely.
Pos : 30 /RVT/Kurz bes chr eibung/Pressautomati k/PA--AAP102 @ 6\mod_1583245266539_18.doc x @ 55489 @ 23 @ 1
7.2 AAP102 pusher tool (Fig. 2)
1
Start button
5
Pusher adapter
7
Expander head
14
Battery
7.2.1 Automatic press cycle (Fig. 2)
The pusher tool features positive control. During compression, the pusher tool remains in the position
reached, even if the start button (1) is temporarily released. When the intended switch-off force is
achieved, it is perceptible by means of an increase in the motor speed and a discernible decrease in
pressure. When the start button (1) is released, the device returns to its initial position. For safety
reasons, the positive control is only activated after a minimum force has been attained. Until this force
is achieved, the pressing operation can be interrupted at any time by releasing the start button (1).
The device then automatically returns to its initial position.
Pos : 31 /RVT/Kurz bes chr eibung/Entriegel ungsknopf/AAP102 @ 0\mod_1382427863945_18.doc x @ 1420 @ 3 @ 1
7.2.2 Release button (5) (Fig. 2)
The release button (5) is used to return the tool to its initial position before the pressing operation has
been completed. In order to do this, press the release button (5) until the pusher adaptor (7) has
moved back completely.
Pos : 32 /RVT/Kurz bes chr eibung/Dr ehbarer Kopf/DK--AAP102 @ 1\mod_1448549759659_18.doc x @ 15628 @ 3 @ 1
7.2.3 Rotatable head (Fig. 2)
The pusher tool is equipped with a rotatable head. It cannot be rotating during the pressing operation.
Pos : 33 /RVT/Kurz bes chr eibung/Sc hiebeadapter/Schi ebeadapter @ 1\mod_1448462990250_18.doc x @ 15484 @ 3 @ 1
7.2.4 Pusher adaptor (Fig. 3)
The nominal width and the name of the system supplier are inscribed on the pusher adapters.
Furthermore, an arrow indicates the installation direction and a number indicates the order. If the
nominal widths for a size are aligned with each other, the arrows and the numbers will be in line.
Pos : 35 /RVT/Kurz bes chr eibung/Akku allgemei n/Ü bers chrift/AA--ÜS--AC O102, ACO152, AC O202XL, AXI/AAP102, @ 0\mod_1382447195475_18.doc x @ 1453 @ 2 @ 1
7.3 Battery
Pos : 36 /RVT/Kurz bes chr eibung/Akku allgemei n/Akku abnehmen + aufsetzen/AAP/AXI102 @ 0\mod_1402922267408_18.doc x @ 2711 @ @ 1
Removing the battery (Fig. 4)
Push in (1) the two release buttons (A) and then remove the battery (2).
Inserting the battery (Fig. 5)
Slide the battery into the device as illustrated until it clicks into place.
Pos : 37 /RVT/Kurz bes chr eibung/Akku allgemei n/Akku Z ustands anzeig e/AC O102, ACO152, AXI/AAP102 @ 0\mod_1382444821884_18.doc x @ 1440 @ @ 1
Battery charge indicator (Fig. 1)
The 4 green LEDs (4) indicate the charge level of the battery. The number of LEDs lit up denotes the
battery charge. If the LED (2) is flashing, the battery is empty and no further travel is possible.
Pos : 38 /RVT/Kurz bes chr eibung/Ger ät + Akku/Info welc her Akku/12V: AAP/AXI102 @ 0\mod_1402925654215_18.doc x @ 2725 @ 2 @ 1
7.4 AXI102 and battery
Pos : 39 /RVT/Kurz bes chr eibung/Akku allgemei n/Info: nic ht geladen + T emperatur en/AA--NG--ACO102, AC O152, ACO/EC O202, ACO202XL, AFP/EF P202, AXI/AAP102 @ 2\mod_1469431352019_18.doc x @ 21590 @ @ 1
Information!
The AXI102 expander and AAP102 pusher tool must only be operated with
12 V DC lithium-ion rechargeable batteries. The 12 V battery must only be used in
the appropriate press devices.
18

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Aap102

Table des Matières