Applications; Spindle Lock - Ryobi CSD41 Manuel D'utilisation

GB
FR DE ES IT
OPERATION
WARNING
Always w ear saf ety goggles or safety glasses
with side shields when operating products .
Failure to do so could result in objects being
thrown into your eyes, resulting in possible
serious injury.
WARNING
Do not use any attachments or accessories not
recommended by the manufacturer of this product.
The use of attachments or accessories not
recommended can result in serious personal injury.

APPLICATIONS

You may use this product for the purposes listed below:
Driving screws with screwdriver bits
■
Light-duty drilling
■
TO CHARGE (Fig. 2)
When charging the screwdriver, a red charge light will
illuminate on the handle of the screwdriver. This red charge
light will go off when the screwdriver is fully charged.
Insert charger plug into input jac k making sure it is
■
properly connected.
Charger can be used with normal household voltage
■
of 230 V, 50Hz, AC only.
Connect charger to power supply.
■
After normal usage, a minimum of 10-12 hours charging
■
time is required to fully recharge the screwdriver.
Do not place charger in an area of extreme heat or
■
cold. It will work best at normal room temperature.
Remove the product from the charger once it is fully
■
charged and ready for use.
WARNING
Battery products are always in operating condition.
Therefore, the switch should always be locked
when not in use or carrying at your side.
ADJUSTABLE TORQUE CLUTCH
This screwdriver is equipped with an adjustable torque
clutch f or dr iving diff erent types of screws into different
materials . The proper setting depends on the type of
material and the size of screw you are using.
ADJUSTING TORQUE (Fig. 3)
There are twelve torque indicator settings located on the
front of the screwdriver.
Rotate adjustment ring to desired setting, aligning
■
number on adjustment ring with arrow on housing.
NL PT DK SE FI NO
English
RU PL CZ HU RO LV
1 - 2 For driving small screws
3 - 4 For driving screws into soft material
5 - 7 For driving screws into soft and hard
materials
8 - 9 For driving screws into hard wood
10 - 11 For driving large screws
For full power applications
D I R E C T I O N O F ROTAT I O N S E L E C TO R
(FORWARD/REVERSE/CENTER LOCK) (Fig. 4)
The direction of bit rotation is reversible and is controlled
by a selector located above the switch tr igger. With
the screwdriver held in normal operating position,
the direction of rotation selector should be positioned
to the left of the switch trigger f or f orward motion.
The direction is re versed when the selector is to the right
of the switch trigger.
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental starting when
not in use.
To stop the screwdriver, release the switch tr igger and
allow the collet to come to a complete stop.
OPERATION
QUICK CHANGE CHUCK (Fig. 5)
A quic k change chuck mounted on the screwdriver is
easy f or inserting or removing the bits. To inser t a bit,
insert the bit into collet till lock. To remove a bit, simply
pull the sleeve of collet forward.

SPINDLE LOCK

The screwdriver spindle is locked when the On/Off switch
is not pressed.
This enab les scre ws to be screwed in, even when the
battery is empty.
GRIP ZONE
Soft grip reduces the danger of slipping and thereby
improves the grip on the tool and handing.
At the same time, the r ubber coating achieves a
vibration-reducing effect.
LED WORKLIGHT (Fig. 6)
The screwdriver has a built-in LED worklight. This feature
is convenient when working in close or tight areas where
additional light is needed. Whenever the switch trigger is
depressed, the LED worklight will illuminate.
NOTE: During normal operation, if the LED worklight will
2
LT EE HR SI SK GR TR