Table Des Matières - Stiga ST 526 S ST 4262 P Manuel D'utilisation

WARNING!: READ THE INSTRUCTION BOOKLET THOROUGHLY
EN
BEFORE USING THE MACHINE. Keep for future reference
INDEX
1. GENERAL INFORMATION ................................... 1
2. SAFETY REGULATIONS ...................................... 2
2.4 Maintenance, storage and transport ............. 3
3. GETTING TO KNOW THE MACHINE ................... 4
3.1 Description of the machine and planned use 4
3.2 Safety signs .................................................. 4
3.3 Identification label ........................................ 5
3.4 Main components ......................................... 5
4. ASSEMBLY ........................................................... 5
4.1 Assembly components ................................. 5
4.2 Assembly of movement and auger control
cables ........................................................... 6
4.3 Handle assembly .......................................... 6
4.4 Installation of the gear control ....................... 6
4.5 Discharge chute assembly............................ 6
4.6 Assembly of the auger extension (ST 627 S) 7
4.7 Levelling skids .............................................. 7
5. CONTROLS .......................................................... 7
5.1 Ignition key .................................................... 7
5.2 Fuel cock ...................................................... 7
5.3 Throttle control .............................................. 7
5.4 Choke control ............................................... 8
5.5 Carburettor ................................................... 8
5.6 Handle for manual start................................. 8
5.7 Electric starter control ................................... 8
5.8 Forward control ............................................. 8
5.9 Steering lever (ST 627 S) .............................. 8
5.10 Auger control ................................................ 8
5.11 Gear stick ..................................................... 8
5.12 Orientation of the chute and deflector (knob
version) (ST 526 S) ....................................... 8
5.13 Orientation of the chute and deflector
(buttons version) (ST 627 S) ......................... 9
5.14 Headlamp switches and handle warming
(optional) ...................................................... 9
6. USING THE MACHINE ......................................... 9
6.1 Preparation ................................................... 9
6.2 Safety checks ............................................... 9
6.3 Start-Up / Operation...................................... 9
6.4 Stop ............................................................ 10
6.5 Advice for operation .................................... 11
6.6 After operation ............................................ 11
7. MAINTENANCE .................................................. 11
7.1 General information .................................... 11
7.2 Refuelling .................................................... 11
7.3 Check / top-up engine oil ............................ 12
7.4 Cleaning ..................................................... 12
7.5 Spark plug .................................................. 12
7.6 Carburettor ................................................. 12
7.7 Nuts and bolts ............................................. 13
7.8 Auger shaft ................................................. 13
8. STORAGE ........................................................... 13
9. ASSISTANCE AND REPAIRS ............................. 13
10. WARRANTY COVERAGE ................................... 13
11. MAINTENANCE TABLE ...................................... 14
12. PROBLEM IDENTIFICATION ............................. 14
1. GENERAL INFORMATION
1.1 HOW TO READ THE MANUAL
Some paragraphs in the manual contain
important information regarding safety and
operation and are emphasized in this manner:
NOTE or IMPORTANT these give details
or further information on what has already been
said, and aim to prevent damage to the machine.
The symbol highlights danger. Non-
compliance with the warning could lead to
personal and/or third party injury and or damage.
The paragraphs highlighted in a square with
grey spots indicate the optional characteristics
not on all models documented in this manual.
Check if the characteristic is on this model.
Whenever reference is made to a position on the
machine "front", "back", "left" or "right" hand side,
this refers to the operator's working position.
1.2 REFERENCES
1.2.1 Figures
The figures in these instructions for
use are numbered 1, 2, 3, etc.
Components shown in the figures
are marked A, B, C, etc.
A reference to component C in figure 2 is
written: "See fig. 2.C" or simply "(Fig. 2.C)".
The figures are given as a guide only. The
actual parts may vary from those shown.
1.2.2 Titles
The manual is divided into chapters and
paragraphs. The title of paragraph "2.1
Training" is a sub-title of "2. Safety regulations".
References to titles or paragraphs are marked
with the abbreviation chap. or par. and the
relevant number. Example: "chap. 2" or "par. 2.1".
EN - 1