Product Description And Specifications; Intended Use; Product Features - Bosch ANGLE EXACT 2 Notice Originale

Masquer les pouces Voir aussi pour ANGLE EXACT 2:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 28
OBJ_BUCH-412-002.book Page 19 Monday, December 9, 2013 5:34 PM
Battery
 Avoid unintentional switching on. Ensure the On/Off
switch is in the off position before inserting battery
pack. Carrying the power tool with your finger on the
On/Off switch or inserting the battery pack into power
tools that have the switch on invites accidents.
 Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and mois-
ture. Danger of explosion.
 Do not short-circuit the battery. There is danger of explo-
sion.
 Battery leakage may occur under extreme usage or
temperature conditions. When a rechargeable battery
leaks, avoid contact with the skin or eyes. The battery
liquid is caustic and could cause chemical burns to tissues.
If liquid comes in contact with skin, wash quickly with soap
and water, then with lemon juice or vinegar. If the liquid
contacts your eyes, flush them with water for a minimum of
10 minutes and seek medical attention.
 Use only original Bosch batteries with the voltage list-
ed on the nameplate of your product. When using other
batteries, e. g. imitations, reconditioned batteries or other
brands, there is danger of injury as well as property dam-
age through exploding batteries.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.

Intended Use

2 | 3 | 6 | 7 | 7–900 | 8 |
ANGLE EXACT
10–650 | 4–420 | 15 | 17 | 23 |
25–200 | 25–250 |
30 | 30–300 | 30–380 |
40–280 | 50–210 | 60–170
The power tool is intended for screwing in and loosening
bolts/screws, nuts and other threaded fasteners in the speci-
fied dimension and performance range.
This power tool is not intended for use as a drill; to avoid per-
sonal injury or damage to the tool, do not use any tool with a
shut-off clutch for drilling purposes.
The light of this power tool is intended to illuminate the power
tool's direct area of working operation and is not suitable for
household room illumination.
14CF | 22CF | 29CF
ANGLE EXACT
Due to its slow left rotation speed, the power tool is intended
for operation with an open flat drive. It is suitable for screw
connections that are only accessible from one side, for exam-
ple, on pipework.
Bosch Power Tools
It is not suitable for loosening screw connections.
This power tool is not intended for use as a drill; to avoid per-
sonal injury or damage to the tool, do not use any tool with a
shut-off clutch for drilling purposes.
The light of this power tool is intended to illuminate the power
tool's direct area of working operation and is not suitable for
household room illumination.

Product Features

The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Tool bit (e.g., socket nut)
2 Tool holder
3 Angled drive head
4 Open-end spanner, size 27 mm
5 Spanner flats on the angled head flange
6 Open-end spanner, size 22 mm
7 Torque selector switch
8 Utility clip
9 LED indicator, tightening control
10 LED indicator, battery condition
11 Battery with contact APT
12 Battery unlocking button
13 On/Off switch
14 Rotational direction switch
15 Fastening slots for utility clip
16 LED holder
17 Marking ring
18 Worklight
19 Spanner flats on the sleeve nut
20 Lock nut
21 Battery charger
22 Power plug
23 Green LED indicator on the battery charger
24 Red LED indicator on the battery charger
25 Connection socket for a voltage adapter on the 4EXACT
26 D-sub connection plug
27 Screws on the D-sub connection plug
28 Voltage adapter
29 Quick-change chuck
30 Adjustment tool
31 Allen key
32 Adjustment disc
33 Motor housing
34 Snap ring
35 Cavity in the housing shell
36 Handle (insulated gripping surface)
37 Handle (insulated gripping surface)
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
English | 19
3 609 929 C62 | (9.12.13)

Publicité

Table des Matières
loading

Table des Matières