01_General Safety Warnings; 02_Instructions For Use; 03_Name And List Of Components; 04_Assembly - Elite ARION MAG Mode D'emploi

Thank you for choosing the ARION MAG
roller

01_GENERAL SAFETY WARNINGS

Before using your trainer, carefully read the warnings listed
below for your health and safety.
1. The appliance is not to be used by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction.
2. Children being supervised not to play with the appliance.
3. Before beginning a training programme, undergo a
physical examination certifying good health.
4. Choose a training level compatible with your physical
e and the status of your health.
enduranc
5. When using the trainer, select a training program and
adjust it so that it is compatible with your fitness level and
health.
6. If you feel particularly fatigued or sore while exercising,
stop using the trainer immediately and consult your doctor.
The above warnings are general and not exhaustive of all
the precautions that should be taken for the proper and
safe use of the trainer; which is solely the responsibility of
the user.

02_INSTRUCTIONS FOR USE

The roller is a training tool enabling users to get into top
shape for cycling.
Its incorporated magnetic resistance unit featuring three
levels offers smoother and more even and gradual
resistance.
The rollers, of technopolymer material, are specially
shaped to guarantee better control of pace.
High quality cylindrical bearings ensure many years of
trouble free and quiet operation.
The frame of the ARION MAG is very practical, light,
manageable, easy to use and takes up little space.
Frame can be folded for easier storage or carrying.
It is recommended for users of all levels.
IMPORTANT
Pay attention to the position of hands when closing the
roller, to avoid squashing them between the two side
members

03_NAME AND LIST OF COMPONENTS

N°3 Side members
N1 Longitudinal member with resistance
N°4 Rectangular covers
N°1 Slider positions 0-1-2
N°1 Front roller
N°1 Middle roller
N°1 Rear roller
N°1 Drive belt
N°1 Allen key

04_ASSEMBLY

Your ARION MAG roller should arrive fully assembled,
checked and ready for use.

05_USE

Before starting to use your ARION MAG it is necessary to
adjust the centre distance of the rollers to make them
compatible with your bicycle's wheelbase.
This adjustment must be carried out as follows:
1) Measure the distance between the centres of the wheels
of the bicycle to be used on the ARION MAG (Fig.2). We
will call this dimension "X".
2) The distance from the intermediate point between the
two rear rollers to the middle of the ARION MAG front roller,
which we will call "Y" (Fig.3), must match or be as near as
possible to dimension "X" . The axle of the ARION MAG
front roller must be positioned in the hole of the ARION
MAG frame whose measurement given on the graduated
scale is closest to dimension "X" (Fig.4).
ATTENTION: Dimension "Y" must be equal to or slightly
greater than "X". The rollers can be adjusted to adapt them
to bicycles whose wheelbase is 944-1124 mm (37 to 44
inches).
3) To change Y it is necessary to shift the front roller E.
4) Fold the ARION MAG until the drive belt H slackens.
5) Loosen the drive belt H , making it come off the
respective front and rear guides.
6) Unfold the ARION MAG back into the open position.
7) Remove the rectangular covers C from both front
longitudinal members (with aid of a screwdriver if
necessary), and the screws and washers from the front
roller on both sides, using the Allen key I) supplied (Fig. 5).
8) Pull the roller out from its original position.
9) Position the roller in the appropriate seat in the holes in
the frame, so that X matches Y.
10) Refit the screws and the washers in the special holes,
but do not tighten them down.
11) Close the ARION MAG, position the drive belt H on the
guide of the front roller E and middle roller F.
12) Unfold the ARION MAG into open position again.
13) Check the position of the front roller E , putting your
bicycle on the rollers and checking that the axle for the
front wheel sits directly above the front roller.
Ref. A
14) Once the front roller E is positioned, tighten the
Ref. B
screws (do not over-tighten as this could warp the side
Ref. C
members).
Ref. D
15) Close the sides with the rectangular covers C. The
Ref. E
ARION MAG is now ready to use.
Ref. F
EN
Ref. G
Ref. H
Ref. I
11