Publicité
Les langues disponibles
Les langues disponibles
has filled up. This acts as a safety against any
unintentional drainage of the boiler.
D
(7)
RAIN
This key works only if the machine has a drain
pump.
It has the desired effect only when the door is
open. Once pushed (LED (j) on), the draining
cycle starts and will continue whether the door
remains open or is closed. By pushing the key
again, the draining cycle stops.
Upon completion of the draining process, the
machine remains stand-by for a few seconds:
after this interval, filling will start again, unless
the user has powered the machine down by
turning main switch off.
Adjustment of Working Temperatures:
(Figure B: Diagram of Electronic Board)
Temperatures are factory-set at:
·55ºC for the wash tank
·87ºC for the boiler
Temperature Adjustment:
In order to be able to adjust the tub and boiler
temperatures, the two microswitches must be in
the OFF position (Elements Disconnect: OFF).
This way, the two elements remain live and
temperatures can be adjusted within the
permissible range: 40 to 70ºC for the tub and
170 to 95ºC for the boiler. Adjusting procedure:
· Check that the two elements are on:
microswitches (3) in the lower position:
"Elements Disconnect: OFF".
·Press the red key (Fig. B-5) during 3 seconds
to activate the temperature setting function.
·The display shows the temperature then
predefined for the tub or the boiler (depending
on how many times you pressed the key - Fig.
A-3).
·To adjust the temperature, there are two
potentiometers: B-2 for the tub and B-4 for the
boiler (both clearly identified on the silk-
screened
board,
that
also
temperature ranges).
·Adjusting is done by turning the relevant
potentiometer clockwise to increase the
temperature and counterclockwise to decrease
it; the display showing the tub or boiler
temperature, whichever has been selected with
key (Fig. A-3).
·After setting the required temperature, power
the machine down and up with main switch A-1.
As a result, the new temperature is stored in the
memory of the electronic board.
Disconnecting the elements:
In order to disable the heating of the elements,
there are two microswitches (3) on the board.
So, placing the two microswitches in the ON
position will disconnect the two elements
(Elements Disconnect: ON).
Troubleshooting:
Only qualified technicians may work on the
connections of the electronic board, after
cutting out power to the machine with the main
switch and the automatic safety circuit-breaker
at the external feeding point to the machine.
The display shows the temperature probes
failure in accordance with the following code:
·E1:.......Boiler probe disconnected (circuit
open). Check the connections at the connector
(Fig B-c)
·E2:.......Boiler probe short-circuited. Probe
failed and must be changed.
·E3:.......Tub probe disconnected (circuit open).
Check the connections at the connector (Fig B-
c)
·E4:.......Tub probe short-circuited. Probe failed
and must be changed.
The temperature transmitters are connected to
the four-pin connector (Fig. B-c).
·E8:........Break-tank fillling failure, 60 seconds
after completion of rinsing, due to a failure of
the inlet solenoid failure, interruption of water
supply, or failure of the level switch.
·E9:........One or more level switches still on 15
seconds after the beginning of a rinse cycle.
This denotes a possible failure of the pressure
pump that does not supply rinsing water or a
failure of a level switch that does not break.
On the electronic board, there are several light
indicators which are very useful for monitoring
the machine operation and malfunction. Those
indicators belong to either of two groups: input
shows
the
LEDs or output LEDs.
Input LEDs: those associated with information
received by the electronic board. Their location
and description are indicated on the silk-
screened board and on Figure B. The following
are amber LEDs:
·'DOOR' LED: ON, when the door is closed.
·'HIGH PRES.' LED: ON, when the high
pressure switch is on, meaning that the tub is
full.
·'LOW PRES.' LED: ON, when the low
pressure switch is on, meaning that the water
level has reached the bottom pressure switch.
·Reserve LED: associated to a spare input.
·'HIGH FLOAT' LED: Break Tank High Float
LED. ON, when the high float has been
actuated, meaning there is water up to this
level.
·'LOW FLOAT' LED: Break Tank Low Float
LED. ON; when the low float has been
actuated, meaning the water level has reached
this point.
Output LEDs: They identify the item that has
been activated by the microprocessor. Their
location and description are indicated on the
silk-screened board and on Figure B. The
following are red LEDs:
·'PRES. PUMP' LED: ON, when the pressure
pump is working.
·'DRAIN PUMP' LED: ON, when the drain
pump is active.
·'S.V.' LED: ON, when water is allowed to flow
through the solenoid valve.
·'WASH. PUMP' LED: ON, when the washing
water pump is operating.
·Reserve LED: associated with a spare output.
·'BOILER RESISTOR CONTACTOR' LED:
ON, when the boiler resistor is heating water.
·TUB RESISTOR CONTACTOR LED: ON,
when the tub resistor is heating water.
Those LEDS show the status of the outputs
activated by the microprocessor. Accordingly,
when one LED is on, the associated component
must also be active.
Example: If the Washing Water Pump LED is
on and the pump does not work, this means that
the microprocessor gives the order correctly
and the fault lies in an external item such as the
contactor or the pump.
The status of the inputs can be determined
according as the respective LEDs are on or off.
Model Configuration:
Control of cycle time (Thermal Lock) as a
function of the boiler temperature:
·The electronic controller features the possibility
of increasing the cycle time until the preset
temperature is reached in the boiler. So, in the
event the temperature of the boiler were lower
than the preset value, the cycle would be
extended until the preset temperature is
7
ENGLISH
Publicité
