Charger Safety - Ryobi CHD-1201 Manuel D'utilisation

GENERAL SAFETY RULES
e) Maintain power tools. Check for misalignment
or bindling of moving parts, breakage of parts and
any other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from intened could result
in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Ensure the switch is in the off position before
inserting battery pack. Inserting the battery pack
into power tools that have the switch on invites
accidents.
b) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
c) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
d) When battery pack is not in use, keep it away
from other metal abjects like paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
SPECIFICATIONS
Model
Voltage
Chuck
Switch
No load speed
Max. Torque
Weight - incl. battery pack
Battery pack
Charger
English
CHD-1201
12 V
0.8-10 mm
Variable speed
0 - 600 min- 1
10 Nm
1.60 kg
BPP-1213/
BPP-1215
BCA-120/
BC-1200/
BC-1215-S
7 7
e) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

CHARGER SAFETY

To reduce risk of injury, charge only nickel-cadmium
■
type rechargeable batteries. Other types of batteries
may burst, causing personal injury and damage.
Do not expose charger to wet or damp conditions.
■
Use of an attachment not recommended or sold by
■
the battery charger manufacturer may result in a risk
of fire, electric shock, or injuries to person.
To reduce risk of damage to charger body and
■
cord, pull by charger plug rather than cord when
disconnecting charger.
Make sure cord is located so that it will not be stepped
■
on, tripped over, or otherwise subjected to damage
and stress.
An extension cord should not be used unless
■
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock.
If extension cord must be used, make sure:
a. That pins on plug of extension cord are the same
number, size and shape as those of plug on charger.
b. That extension cord is properly wired and in good
electrical condition.
CHD-1441
14.4 V
0.8-10 mm
Variable speed
0 - 650 min- 1
12 Nm
1.77 kg
BPP-1413/
BPP-1415
BCA-144/
BC-1440/
BC-1415-S
CHD-1801
18 V
0.8-10 mm
Variable speed
0 - 650 min- 1
16 Nm
1.96 kg
BPP-1813/
BPP-1815
BCA-180/
BC-1800/
BC-1815-S