Residual Risks - LEMAN SOR250 Manuel D'utilisation

17. Never remove any cut-offs or other parts of the workpiece from the cutting area whilst the tool is
running with an unguarded saw blade.
18. Do not perform any operation freehand. The workpiece must be secured firmly against the turning table and
guide fence with the vise during all operations. Never use your hand to secure the workpiece.
19. Ensure that the tool is stable before each cut.
20. Fix the tool to a work bench, if needed.
21. Support long workpieces with appropriate additional supports.
22. Never cut so small workpiece which cannot be securely held by the vise. Improperly held workpiece may
cause kickback and serious personal injury.
23. Never reach around saw blade.
24. Turn off tool and wait for saw blade to stop before moving workpiece or changing settings.
25. Unplug tool before changing blade or servicing.
26. Release knob which locks the cutter head down is for carrying and storage purposes only and not for
any cutting operations.
27. Do not use the tool in the presence of flammable liquids or gases. The electrical operation of the tool
could create an explosion and fire when exposed to flammable liquids or gases.
28. Use only flanges specified for this tool.
29. Be careful to not damage the arbor, the flanges (especially the installing surface) or the bolt. Damage to
these parts could result in blade breakage.
30. Make sure that the turning table is properly secured so it will not move during operation.
31. For your safety, remove the chips, small pieces, etc. from the table top before operation.
32. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation.
33. Make sure the spindle lock is released before the switch is turned on.
34. Be sure that the blade does not contact the turning table in the lowest position.
35. Hold the handle firmly. Be aware that the saw moves up or down slightly during start-up and stopping.
36. Make sure the blade is not contacting the workpiece before the switch is turned on.
37. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that
could indicate poor installation or a poorly balanced blade.
38. Wait until the blade attains full speed before cutting.
39. Stop operation immediately if you notice anything abnormal.
40. Do not attempt to lock the trigger in the on position.
41. Always use accessories recommended in this manual. Use of improper accessories may cause an injury.
42. Take care when slotting.
43. To reduce the emitted noise, always be sure that the blade is sharp and clean.
44. Provide adequate lighting.
45. Ensure that you are trained in the use, adjustment and operation of the machine.
46. Do not overreach. Keep proper footing and balance at all times.
47. Remove adjusting keys and wrenches. Form the habit of checking to see that keys and adjusting wrenches
are removed from the tool before turning it on.
48. Avoid unintentional starting. Ensure switch is in "off" position when plugging in.
49. Do not slow or stop a blade with a piece of wood. Let the blade come to rest naturally.
50. Periodically check that all nuts, bolts and other fixings are properly tightened.
51. During slide cutting, always ensure that the saw blade is pushed away from the operator.

2. Residual risks

Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules out.
The following hazards may arise in connection with the equipment's construction and layout:
- Contact with the blade.
- Kickback of workpiece and parts of workpiece.
- Blade fracture.
- Catapulting of blade pieces.
- Lung damage if no suitable protective dust mask is used.
- Damage to hearing if no suitable ear protection is used.
- Health damage caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly
guided and maintained.
3. Danger due to the laser
- Laser product Class 2M, Red Laser, Wave Length 650 nm, Power <1mW, EN 60825-1: 2007.
- Do not stare into beam.
- The instrument is not allowed to disassemble or repair in any ways.
GB
27