Replacing The Power Cable; Ordering Replacement Parts; Cleaning, Maintenance And Ordering Of Spare Parts; Disposal And Recycling - EINHELL BG-RS 2845/1 CB Mode D'emploi D'origine

Anleitung_BG_RS_2845_1_CB_SPK7:_
GB
6.8 Adjusting the counter blade (Fig. 14)
The counter blade and cutting unit are perfectly
adjusted at the factory. Only if it suffers wear does
the counter blade require adjustment (switch the
machine on for this purpose). To ensure the best
possible results from your shredder, the gap between
the counter blade (item B) and the shredding blade
(item A) should be approx. 0.50 mm.
There is an adjustment device on the right-hand side
of the plastic housing for this purpose. Turn the knob
clockwise so that the screw (item C) moves towards
the shredding blade. After a half-turn the counter
blade will have moved 0.50 mm closer to the
shredding blade. After completing this adjustment
check whether the blade produces the desired
results.
IMPORTANT: If the shredding blade touches the
counter blade, it will cut it and small metal chips may
fall out of the discharge opening. This is not a fault,
but it must only be adjusted as much as necessary
since otherwise the counter blade will suffer
premature wear.
When the counter blade cannot be adjusted any
more, it has reached its wear limits and must be
replaced.
Important: Wear work gloves!
Remove the cover from the cutting unit (Fig. 15/Item
A) by removing the 4 Allen screws (Fig. 15/Item B).
The counter blade (Fig. 16/Item B) can now be taken
out. Insert a new counter blade (you must turn the
adjustment device counter-clockwise until the new
counter blade fits in the mount). Fit the cover with the
4 Allen screws. Then adjust the counter blade
correctly as described under 6.8.

7. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
8. Cleaning, maintenance and ordering
of spare parts
Always pull out the mains power plug before starting
any cleaning work.

8.1 Maintenance and storage

Clean the machine regularly. This will help to
keep the machine in good working order and is
16
21.12.2011 8:37 Uhr Seite 16
the basis for a long working life.
Keep the vent slots clean while you work.
Clean the plastic body and other plastic parts
with a mild household cleaning agent and a
damp cloth. Do not use any aggressive agents or
solvents for cleaning purposes.
Never clean the shredder by spraying with water.
Prevent water getting inside the machine at all
cost.
Check the chassis securing screws from time to
time to ensure that they are tight.
If you do not intend to use the shredder for a
lengthy period, protect it from corrosion using
environmentally friendly oil.
Store the device in a dry room.
Store the device out of reach of children.
The equipment must be cleaned and conserved
at the end of the season.
Important: Wear work gloves!
Remove the cover from the cutting unit (Fig. 15/Item
A) by removing the 4 Allen screws (Fig. 15/Item B).
You can now take out the counter blade (Fig. 16/Item
B) and the cutting unit (Fig. 16/Item A). Clean the
cutting compartment, the counter blade and the
cutting unit and cover them with a thin coat of
vegetable oil before installing everything again. At the
beginning of the new season the counter blade must
be correctly adjusted as described under 6.8.

8.2 Ordering replacement parts

Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info

9. Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.