Year Guarantee - Esselte LEITZ wireBIND 300 Guide D'utilisation

Punching and Binding
Selecting and Inserting the Wire Comb
•
Determine the required comb size using the table in
this manual.
•
Insert the wire comb with the open side facing
upwards into the hook of the wire comb holder
Punching
•
Turn the adjustment knob
The sheets are only correctly punched in this position.
Tip: Test the punching result initially with a blank sheet of
paper before you punch the original.
•
Place the sheets in the punching channel
•

Press the lever
•
Remove the punched sheets.
Inserting Punched Sheets
•
Insert the punched sheets into the wire comb.
You can now punch all the remaining sheets and insert them
into the wire comb.
Closing the Wire Comb
Please note that once a wire comb has been closed it can
only be opened again by destroying it.
•
Turn the adjustment knob
used.
The setting is important so that the wire comb can be
correctly closed.
•
Remove the wire comb together with the inserted
sheets from the wire comb holder.
•
Place the sheets with the open side of the wire comb
facing downwards in the wire comb closer
•
Press the binding lever down slowly as far as it will
go and then raise it again.
•
Remove the bound document.
Specifications
Mode of operation
Paper format
Punching blades
Punching capacity
Wire comb size
Net weight
Dimensions (B x D x H)
Subject to technical modifications without notice.
G
to "Punch Point".
B
down and then raise it again.
G
to the comb size being

34 (3:1 pitch)
15 sheets of paper (80 g/m²) or
2 transparent films (0.2 mm)
6–14 mm (up to 120 sheets)
400 mm x 330 mm x 350 mm

3 year guarantee

To be returned with the unit if defective.
LEITZ units are sold with a 3 year guarantee.
The conditions of the guarantee period of 3 years are as
follows:
1. Each unit is guaranteed against all defects in material
and/or workmanship for a period of 3 years from the
C
.
date of purchase.
No unit will be accepted without written notification
2.
from the customer giving details of the problem that
has occurred, and proof of the date of purchase.
3. All units for repair are to be returned to Esselte with
adequate packaging. No liability will be accepted
by Esselte for goods damaged in transit from the
customer, due to inadequate attention to packaging.
.
4. The supplier will be responsible for all parts and labour
charges as necessary to the unit. The 3 year guarantee
is subject to the following conditions:
a)
That the unit has been used strictly in accordance
with the operating instructions supplied with the
unit.
b) That if the benefit of this guarantee is sought, the
unit must be returned, carriage paid to Esselte.
Esselte does not accept responsibility for loss or
damage in transit.
c)
That the guarantee is invalid if the defects are
found to be caused by accident, misuse, alteration
or neglect.
d)
That no liability of Esselte is to be implied here
for damage, loss or expense of any kind resulting
from, consequence upon, or in any way due
to any fault whatsoever in the instrument or its
accessories.
e)
That this guarantee does not affect you statutory
rights as a consumer.
.
Date of Purchase:
Model No. Serial No.:
Company Name:
Contact person:
Manual
Address:
A4
Telephone/Fax No:
ESSELTE UK Ltd.
Waterside House, Cowley Business Park,
Uxbridge, Middlesex,
7.3 kg
UB8 2HP
UNITED KINGDOM
Tel.: 0870 9090609
Fax: 01895 878901
Esselte Ireland Limited
Westlink Industrial Estate,
Kylemore Road,
Dublin 10
IRELAND
Tel: +353-1-6268438
Fax: +353-1-6269798
www.esselte.ie

5