Layout And Items Supplied; Safety Regulations - EINHELL GC-RS 2540 CB Instructions D'origine

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Description of the warning sign (see Figure
16) on the machine
1: Important! Read the operating instructions
and follow the warnings and safety instruc-
tions
2: Take care when the blades are rotating. Do
not put your hands or feet into openings when
the machine is running.
3: Important! Keep other persons and animals
away from the danger zone.
4: Important! Protect the machine from the
damp and never expose it to rain.
5: Important! Always wear safety goggles, ear
muff s, protective gloves and heavy-duty work
clothes!
6: Always set the ON/OFF switch to OFF and
pull the power plug out of the socket-outlet
before doing any work on the shredder, e.g.
cleaning the shredder and making adjust-
ments, or if
the power cable becomes damaged.
7: Explanation of the safety switch on the deb-
ris box: The switch is in the "Lock is closed"
position: The shredded material debris box is
locked. The shredder can be switched on. The
switch is in the "Lock is open" position: The
shredded material debris box is not locked
and can be removed. The shredder cannot be
Anl_GC_RS_2540_2845_CB_SPK1.indb 17 Anl_GC_RS_2540_2845_CB_SPK1.indb 17
GB
switched on.
8: Explanation of the lever for adjusting the
counter blade:
Turning clockwise reduces the distance bet-
ween the cutting unit and the counter blade.
Turning counter-clockwise increases the
distance between the cutting unit and the
counter blade.
9. Changeover switch: For a description of the
changeover switch see point 6.4

2. Layout and items supplied

2.1 Layout (Fig. 1-3)
1. Motor unit
2. Shredded material debris box
3. Base frame
4. Wheels
5. Wheel caps
6. Knob for setting the counter blade
7. Power plug
8. Transport handle
9. Reverse running switch
10. ON/OFF switch
11. Legs (including fastening screw)
12. 4x screws for fi tting the motor unit
13. 4x washers for fi tting the motor unit
14. 2x sets of screws for fi tting the wheels (inclu-
ding wheel sleeves, washers and nuts)
15. Funnel
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
- 17 -
16.07.15 14:44 16.07.15 14:44