JVC KD-R975BTS Manuel D'instructions page 25

AUDIO SETTINGS
EQ SETTING
EQ PRESET
Select a preset equalizer suitable to the music genre. (Select [USER]
to use the settings made in [EASY EQ] or [PRO EQ].)
FLAT / HARD ROCK / POP / HIP HOP / R&B / JAZZ / CLASSICAL /
USER
EASY EQ
Adjust your own sound settings. The settings are stored to [USER].
• The settings made may affect the current settings of [PRO EQ].
SUB.W SP *
*
1 2
:
SUB.W *
1 * 3
:
BASS LVL:
MID LVL:
TRE LVL:
PRO EQ
Adjust your own sound settings. The settings are stored to [USER].
• The settings made may affect the current settings of [EASY EQ].
62.5HZ
LVL –09 to +09 (00): Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
BASS EXT ON: Turns on the extended bass. ; BASS EXT OFF: Cancels.
100HZ / 160HZ / 250HZ / 400HZ / 630HZ / 1KHZ / 1.6KHZ / 2.5KHZ /
4KHZ / 6.3KHZ / 10KHZ / 16kHZ
LVL –09 to +09 (00): (Refer above)
Q FACTOR
Q 1.35/ Q 1.50/ Q 2.00: Adjust the quality factor.
AUDIO
BASS BOOST +01 — +05: Selects your preferred bass boost level. ; OFF: Cancels.
LOUD 01 / 02: Boosts low or high frequencies to produce a well-balanced
sound at low volume. ; OFF: Cancels.
Default: XX
00 to +06 (Default: 03
–50 to +10 00
–09 to +09 00
–09 to +09 00
–09 to +09 00)
SUB.W LEVEL * SPK-OUT *
1 2
(Not applicable when 3-way crossover is selected.)
00 to +06 (+03): Adjusts the output level of the subwoofer
connected via speaker lead. ( 34, 35)
PRE-OUT * –50 to +10 (00): Adjusts the output level of the subwoofer
3
connected to the lineout terminals (SW or REAR/SW) through an
external amplifier. ( 34, 35)
SUB.W * ON / OFF: Turns on or off the subwoofer output.
3
FADER
(Not applicable when 3-way crossover is selected.)
R15 — F15 (00): Adjusts the front and rear speaker output balance.
BALANCE * L15 — R15 (00): Adjusts the left and right speaker output balance.
4
VOL ADJUST –15 — +06 (00): Preset the initial volume level of each source (compared to
the FM volume level). Before adjustment, select the source you want to adjust.
AMP GAIN LOW POWER: Limits the maximum volume level to 25. (Select if the maximum
power of each speaker is less than 50 W to prevent damaging the speakers.) ;
HIGH POWER: The maximum volume level is 35.
SPK/PRE OUT
(Not applicable when 3-way crossover is selected.)
Depending on the speaker connection method, select the appropriate setting to
get the desired output. ( 22, Speaker output settings)
SPK SIZE Depending on the crossover type you have selected (see [X ' OVER TYPE]
below), 2-way crossover or 3-way crossover setting items will be shown. ( 23,
Crossover settings)
X ' OVER
By default, 2-way crossover type is selected.
X ' OVER TYPE Caution: Adjust the volume before changing the X ' OVER TYPE to avoid the
sudden increase or decrease of the output level.
X ' OVER 2-WAY (Displayed only when [X ' OVER 3-WAY] is selected)
YES: Selects two way crossover type. ; NO: Cancels.
X ' OVER 3-WAY (Displayed only when [X ' OVER 2-WAY] is selected)
YES: Selects three way crossover type. ; NO: Cancels.
*
1
Displayed only when [SUB.W] is set to [ON].
*
2
For 2-way crossover: Displayed only when [SPK/PRE OUT] is set to [SUB.W/SUB.W]. ( 22)
*
3
For 2-way crossover: Displayed only when [SPK/PRE OUT] is set to [REAR/SUB.W] or [SUB.W/
SUB.W]. ( 22)
*
4
This adjustment will not affect the subwoofer output.
21
ENGLISH