Ryobi RPP750S Traduction Des Instructions Originales page 4

less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc,
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
ADDITIONAL GENERAL SAFETY WARNINGS
Some regions have regulations that restrict the use of
the product. Check with your local authority for advice.
Never allow children or people unfamiliar with the
instructions to use the product. Local regulations may
restrict the age of the operator.
Ensure before each use that all controls and safety
devices function correctly. Do not use the product if the
"off" switch does not stop the motor.
Wear full eye and hearing protection, strong sturdy
gloves as well as head protection while operating the
product; use a face mask if operation is dusty.
Do not wear loose fitting clothing, short trousers or
Secure long hair so it is above shoulder level to prevent
entanglement in moving parts.
bystanders, children, and animals at least 15 m away
from work area.
Do not operate in poor lighting. The operator requires a
clear view of the work area to identify potential hazards.
Use of hearing protection reduces the ability to hear
warnings (shouts or alarms). The operator must pay
extra attention to what is going on in the working area.
Operating similar tools nearby increases both the risk
enter your working area.
Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance and can
increase the risk of kickback.
Keep all parts of your body away from any moving part.
Inspect the machine before each use. Check for correct
operation of all controls. Check for loose fasteners,
make sure all guards, and handles are properly and
securely attached. Replace any damaged parts before
use.
Do not modify the machine in any way or use parts
and accessories which are not recommended by the
manufacturer.
Do not let familiarity gained from frequent use of
machines allow you to become complacent and ignore
tool safety principles. A careless action can cause
Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of
2 | English
the tool in unexpected situations.
If you need to use an extension cable ensure it is
suitable for outdoor use and has a current capacity
sufficient to supply your tool. Check it before every use
for damage. Always uncoil it during use because coiled
cables can overheat.
WARNING
If the machine is dropped, suffers heavy impact or begins
to vibrate abnormally, immediately stop the machine and
inspect for damage or identify the cause of the vibration.
Any damage should be properly repaired or replaced by
an authorised service centre.
PRUNER SAFETY WARNINGS
Never use the pruner when there is a possibility of
thunderstorm or lightning. Store the pruner and the
power cables safely indoors.
Ensure all guards, handles are properly fitted and are
in good condition.
Do not start using the product until you have a clear
work area, secure footing, and a planned retreat path
away from the falling branches or limbs.
Beware of the emission of lubricant mist and saw dust.
Wear mask or respirator if required.
Electrical power should be supplied via a residual
current device (RCD) with a tripping current of not more
than 30 mA.
If the power cable becomes damaged, you must return
the machine to an authorised service centre for repair
or replacement.
Always hold the pruner with both hands when operating
it. Use one hand to firmly grasp the front hand grip. Use
the other hand to grasp the rear handle and operate the
Hold the power tool by insulated gripping surfaces only,
because the saw chain may contact hidden wiring.
Saw chains contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
Do not modify your tool in any way or use it to power
any attachments or devices not recommended by the
manufacturer for your pruner.
Your pruner comes with a harness. You must use it
whilst operating the pruner. It will assist you to control
the drop of the pruner after the cut is completed. It will
also help support the weight of the machine during use
and whilst moving between pruning positions.
Identify the quick release mechanism and practice
using it before you start using the machine. Its
an emergency. Never wear additional clothing over
the harness or otherwise restrict access to the quick
release mechanism.
Before starting the tool, make sure the saw chain is not