Preparing The Mower For Long-Term Storage; Preparing The Mower For Transport; Ordering Replacement Parts; Disposal And Recycling - EINHELL BG-PM 51 S HW-E Mode D'emploi D'origine

Arrange for your customer service or an autho-
rized workshop to do the work. The same applies
to accessory parts.
7.2.9 Operating times
Please observe the regulations concerning lawn
mower operating times, which may diff er from
town to town.
7.2.10 Maintenance and care of the battery
•
Ensure that your battery is always fitted secu-
rely.
•
A perfect connection to the cable network of
the electrical system must be ensured at all
times.
•
Keep the battery clean and dry.
7.3 Preparing the mower for long-term sto-
rage
Warning: Do not empty the petrol tank in enc-
losed areas, near fi re or when smoking. Petrol
fumes can cause explosions and fi re.
1. Drain the petrol tank using a petrol extraction
pump.
2. Start the engine and run it until the tank and
fuel line are completely empty and the engine
stalls.
3. Change the oil after each season. To do so,
remove the used engine oil when the engine
is warm and refi ll new oil.
4. Remove the spark plug from the cylinder
head. Use an oil can to fi ll the cylinder with
approx. 20 ml of oil. Slowly pull back the star-
ter handle, which will bathe the cylinder wall
with oil. Screw the spark plug back in.
5. Clean the cooling fi ns of the cylinder and the
housing.
6. Be sure to clean the entire equipment to pro-
tect the paint.
7. Store the equipment in a well-ventilated place
or location.
8. Remove the battery if you intend to put the
lawn mower into storage for any longer than 3
months.
Please read the safety information on the batte-
ries (point 3) for information concerning the sto-
rage of the battery.
Anl_BG_PM_51_S_HW_E_SPK7.indb 41 Anl_BG_PM_51_S_HW_E_SPK7.indb 41
GB

7.4 Preparing the mower for transport

1. Empty the petrol tank (refer to point 7.3/1)
2. Always let the engine run until it has used up
the remainder of petrol in the tank.
3. Empty the engine oil from the warm engine.
4. Remove the spark plug boot from the spark
plug.
5. Clean the cooling fi ns of the cylinder and the
housing.
6. Unhook the starter cable from the hook (Fig.
3c). Slacken the star nuts and fold down the
upper push bar. Make sure that the cables do
not get kinked when the bar is pulled up.
7. Wedge a few layers of corrugated cardboard
between the upper and lower push bars and
the engine in order to prevent any chafi ng.
7.5 Consumables, wear materials and spare
parts
Spare parts, consumables and wear materials
such as engine oil, V-belts, spark plugs, air fi lter
inserts, petrol fi lters, batteries and blades are not
covered by the warranty.

7.6 Ordering replacement parts

Please provide the following information on all
orders for spare parts:
•
Model/type of the equipment
•
Article number of the equipment
•
ID number of the equipment
•
Part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info

8. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Defective components must be dispo-
sed of as special waste. Ask your dealer or your
local council.
- 41 -
20.02.12 09:27 20.02.12 09:27