Night Well-Being Key; Setting The Operating Programs; Setting The Exact Time; Setting The Times Of The 1St And 2Nd The Operating Programs (Progr. 1 And Progr. 2) - Unico Digitemp Manuel D'installation, Emploi Et Entretien

3.3.12

Night well-being key

Press the night well-being T3 button to obtain several results, specifically:
- Gradual increase of the set cooling temperature.
- Gradual decrease of the temperature set for heating (only HP models).
- Decrease of the unit's noise level.
- Savings on night-time consumption of electricity.
In order to activate the Night well-being key press button T3 after having selected the required operating mode through
button T4 and having set the required temperature through button T7.
Ideally, you should start night well-being mode operation just before you fall asleep.
In cooling, the set temperature is maintained for one hour after activating the night-time comfort button. During the next two hours
the setting increases gradually, whilst the running of the fan is set to low speed. After the second hour, the temperature and fan
speed settings do not change any longer.
In heating mode, the set temperature is held for one hour after starting Night well-being mode operation.
During the next two hours the setting decreases gradually, whilst the running of the fan is set to low speed.
After the second hour, the temperature and fan speed settings do not change any longer.
The 'night well-being' key is not available when the unit operates in dehumidification and ventilation mode.
The night well-being mode button may be disabled at any time (ideally when you wake up in the morning) by pressing button T3 again.
At this stage the temperature and fan speed settings made prior to starting Night well-being mode operation go back into effect.
3.3.13

Setting the operating programs

The air conditioner logic provides the user with a choice of two operating programs that can be set to start and stop at programmed
times, for example you might want the air conditioner to start shortly before you return home so that it is cool when you get there.
To use these functions it is first necessary to set the exact time on the remote control and then set the time for the programs to start.
3.3.14

Setting the exact time

Proceed as follows to set the exact time:
a) Press button T6 (Time and Program Setting), as many times as necessary to display the hour indication H (D10).
b) Press the toggle button T7 to increase or decrease the displayed hour until it matches the exact time.
c) Press button T6 again to display the minutes indication M (D10).
d) Press the toggle button T7 to increase or decrease the displayed minutes until it shows the exact time in minutes.
3.3.15

Setting the times of the 1st and 2nd the operating programs (PROGR. 1 and PROGR. 2)

To set the times for starting and stopping the two air conditioner programs, proceed as follows:
a) Press button T6 (Time and Program Setting), as many times as necessary to display the indication
program).
b) Press the toggle button T7 to increase or decrease the display of the time when you want program 1 to start.
Every time you press one end of the toggle button the time increases or decreases by 30 minutes.
c) Press button T6 (Time and Program Setting) once again to display the indication
d) Press the toggle button T7 to increase or decrease the indication of the time when you want program 1 to stop. Every time
you press one end of the toggle button the time increases or decreases by 30 minutes.
e) Press button T6 (Time and Program Setting) once again to display the indication
f) Press the toggle button T7 to increase or decrease the display of the time when you want program 2 to start.
Every time you press one end of the toggle button the time setting increases or decreases by 30 minutes.
g) Press button T6 (Time and Program Setting) once again to display the indication
h) Press the toggle button T7 to increase or decrease the indication of the time when you want program 2 to stop. Every time
you press one end of the toggle button the time increases or decreases by 30 minutes.
i) To return to the routine operating mode just press the button T6 as many times as necessary to clear the relevant indications
from the display.
3.3.16

Starting and stopping the operating programs

After having made the settings for the operating programs, they can be used or not, as needed.
Either or both of the programs can be used.
In particular, each time you press the button T11 (Program activation), the situation changes as follows:
Use of Program no. 1 only.
Use of Program no. 2 only.
Use of Programs 1 and 2.
Disuse of both programs.
AUTO ECO
AUTO
1
(Time to start the 1st
2
AUTO ECO
AUTO
1
(Time to stop the 1st program).
H
AUTO ECO
AUTO
2
M
1
H
+
F S
2
(Time to start the 2nd program). A E
M
AUTO ECO
N T
AUTO
-
1
H
2
+
(Time to stop the 2nd program).
F S
M
A E
N T
-
+
F S
A E
N T
-
+
F S
A E
N T
-
3
H
M
21