Electrical Connection - Ryobi EMS-2026SCL Manuel D'utilisation

GB
F D
SPECIFICATIONS
Cutting Capacity
Mitre 90° x Bevel 90°
Mitre 45° (R) x Bevel 90°
Mitre 45° (L) x Bevel 90°
Mitre 90° x Bevel 45°
Mitre 45° (R) x Bevel 45°
Mitre 45° (L) x Bevel 45°
ASSEMBLY
WARNING
To prevent accidental starting that could cause
possible serious personal injury, assemble all
parts, make sure all adjustments are complete,
and make sure all fasteners are secure before
connecting saw to power supply. Saw should
never be connected to power supply when you
are assembling parts, making adjustments,
installing or removing blades, or when not in use.
VICE ATTACHMENT (Fig. 1 & 2)
To attach the vice (12), push the round attachment rod
into the vice attachment hole and turn the rear locking
knob (23) in a clockwise direction to lock.
MATERIAL SUPPORTS (Fig. 3, 4 & 5)
Slide the support arm (8) into the holes of the base.
■
Ensure the rod also goes through the clamp bracket.
Tighten the screw on the clamp bracket when the rod
is fully inserted.
Insert the second support arm bracket on the other
■
side of the saw base and repeat the process. The
support arm brackets should be diagonally opposite
each other for greater stability.
DUST BAG (Fig. 6)
Attach the dust bag (17) by compressing the metal spring
together.
LOCK DOWN PIN (Fig. 7)
Your compound mitre saw features a lock down pin (14)
for easier transportation. To unlock the head pull the pin
out and lift up the saw arm to the upright position.
SLIDE LOCK (Fig. 8)
To prevent sliding movement of the saw head during
transportation, fasten the slide lock (21).
E I P NL
90 mm x 305 mm
90 mm x 215 mm
90 mm x 215 mm
42 mm x 305 mm
42 mm x 215 mm
42 mm x 215 mm
S DK N FIN
English
0°-45° MITRE ADJUSTMENT (Fig. 9)
Your compound mitre saw cuts from 0° to 45° both right
and left, with positive stops at 0, 15, 22.5, 30 and 45
degrees. Loosen the mitre table lock knob (9) by turning
counterclockwise direction and move the mitre table to the
desired cutting angle. Re-tighten the mitre table lock knob
to lock table in position, by turning clockwise direction.
FENCE (Fig. 9)
The rear fence (13) on your sliding compound mitre saw
has been provided to hold your workpiece securely
against when making all cuts.
SELF-RETRACTING LOWER BLADE GUARD
(Fig. 10)
The lower blade (4) guard is made of shock-resistant,
see-through plastic that provides protection from each
side of the blade. It retracts over the upper blade guard
as the saw is lowered into the workpiece.
WARNING
Your sliding compound mitre saw has 4 holes for
mounting to the workbench. Always make sure
your compound mitre saw is securely mounted to
a workbench or an approved workstand. Failure
to do so could result in an accident causing
serious personal injury.

ELECTRICAL CONNECTION

Your saw has a precision built electric motor. It should
only be connected to an AC supply of the type specified
on the rating plate. Do not operate this tool on direct
current (DC). A substantial voltage drop will cause a loss
of power and the motor will overheat. If your tool does not
operate when plugged into an outlet, double check the
power supply.
WARNING
The operation of any power tool can result in
foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning
power tool operation, always wear safety goggles
or safety glasses with side shields and a full face
shield when needed. We recommend a Wide
Vision Safety Mask for use over eyeglasses or
standard safely glasses with side shields.
WARNING
Do not attempt to modify this tool or create
accessories not recommended for use with
this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
16
GR H CZ RUS RO PL