Servo Adjustment - Horizon Hobby BLADE 360CFX 3S BNF BASIC Manuel D'utilisation

Servo Adjustment

Your Blade 360 CFX 3S was setup at the factory and test fl own. The servo adjust-
ment steps are usually only necessary in special circumstances, such as after a
crash or if a servo or linkage is replaced.
WARNING: To ensure your safety, always disconnect the motor wires from the
ESC before performing the following steps. After you have completed the adjust-
ments, reconnect the motor wires to the ESC before attempting to fl y the model.
Entering Servo Adjustment Mode
DX6G2, DX6e and DX6i Users:
1. Lower the throttle stick to the lowest position.
2. Power ON the transmitter.
3. Install the fl ight battery on the helicopter frame, securing it with the hook and
loop strap.
4. Connect the battery connector to the ESC.
5. Before initialization is complete, hold
the left stick to the bottom left corner
and the right stick to the bottom right
corner as shown.
6. When the swashplate servos move,
you have entered Servo Adjustment
Mode.
Adjusting the Servo Neutral Position
With the model in Servo Adjustment Mode, the control stick and gyro inputs are
disabled and the servos are held in the neutral position. Check the position of the
servo arms to see if they are perpendicular to the servos.
• If the arms are perpendicular to the servos, no adjustment is necessary.
Exit Servo Adjustment Mode.
• If one or more servo arm is not perpendicular to the servos, continue the servo
adjustment process.
While watching the swashplate servos, apply right cyclic and release. One of the
servos will jump, indicating which servo is selected. Press right cyclic and release
until the servo that needs to be adjusted is selected.
Once the servo you wish to adjust is selected, move the cyclic stick forward or
backward to adjust the servo neutral position in the desired direction.
If you would like to reset the current servo to the default neutral position, hold the
rudder stick full right for 1 second.
The range of adjustment is limited. If you are unable to adjust the servo arm to be
perpendicular to the servo, you must reset the servo to the default neutral position,
remove the servo arm and place it back onto the servo as close to perpendicular
as possible. You may then adjust the servo neutral position using the forward/
backward cyclic stick.
EN
7. Release the sticks and proceed to Adjusting the Servo Neutral Position to make
any desired changes.
DX7s / DX7 G2 / DX8 / DX8 G2 / DX9 / DX18 / DX20 Users:
1. Lower the throttle stick to the lowest position.
2. Power ON the transmitter.
3. Install the fl ight battery on the helicopter frame, securing it with the hook and
loop strap.
4. Connect the battery connector to the ESC.
5. Place the helicopter on a fl at surface and leave it still until the orange receiver
LED glows solid, indicating initialization is complete.
6. Hold the left stick to the bottom left
corner and the right stick to the bot-
tom right corner as shown.
7. Hold the bind/panic switch until the
swash servos move.
8. Release the sticks and the bind/panic switch. The model is now in Servo
Adjustment Mode.
9. Proceed to Adjusting the Servo Neutral Position to make any desired changes.
Swashplate Leveling
Before saving your adjustments and exiting servo adjustment mode, verify the
swashplate is level and both main rotor blades are at 0 degrees.
If they are not, make linkage adjustments as necessary.
Saving the Servo Adjustments
DX6, DX6e, and DX6i Users:
1. Lower the throttle stick to the lowest position and release the sticks.
2. Move the tail rotor stick to the left and hold until the servos move.
3. Release the tail rotor stick to save the servo adjustments.
4. Reconnect the main drive motor to the ESC. Your model is now ready for fl ight.
DX7s / DX7 G2 / DX8 / DX8 G2 / DX9 / DX18 / DX20 Users:
1. Lower the throttle stick to the lowest position and release the sticks.
2. Press and hold switch I until the swash servos move.
3. Release switch I to save the servo adjustments.
4. Reconnect the main drive motor to the ESC. Your model is now ready for fl ight.
All of the settings are stored internally, so your adjustments will be maintained
each time you initialize the model.
11
EN