Additional Safety Instructions; Technical Data; Before Starting The Equipment - Scheppach HC105DC Traduction Des Instructions D'origine

Additional safety instructions

Safety instructions for working with compressed air
and blasting guns
• The compressor pump and lines can become
very hot during operation. Touching these parts
will burn you.
• The air which is sucked in by the compressor must
be kept free of impurities that could cause fires or
explosions in the compressor pump.
• When releasing the hose coupling, hold the hose
coupling piece with your hand. This way, you can
protect yourself against injury from the rebound-
ing hose.
• Wear safety goggles when working with the blow-
out pistol. Foreign bodies or blown off parts can
easily cause injuries.
• Do not blow at people with the blow-out pistol and
do not clean clothes while being worn. Risk of injury!
Warning! This electric tool generates an electro-
magnetic field during operation. This field can im-
pair active or passive medical implants under certain
conditions. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
Safety information for paint spraying
• Do not process any paints or solvents with a flash
point below 55° C. There is a risk of explosion!
• Do not heat up paints or solvents. There is a risk
of explosion!
• If hazardous liquids are processed, wear protec-
tive filter units (face guards). Also, adhere to the
safety information provided by the manufacturers
of such liquids.
• The details and designations of the Ordinance on
Hazardous Substances, which are displayed on
the outer packaging of the processed material,
must be observed.
• Additional protective measures are to be undertak-
en if necessary, particularly the wearing of suitable
clothing and masks.
• Do not smoke during the spraying process and/or
in the work area. There is a risk of explosion! Paint
vapors are easily combustible.
• Never set up or operate the equipment in the vicini-
ty of a fire place, open lights or sparking machines.
• Do not store or eat food and drink in the work area.
Paint vapors are harmful to your health.
• The work area must exceed 30 m
ventilation must be ensured during spraying and
drying. Do not spray against the wind. Always ad-
here to the regulations of the local police authority
when spraying combustible or hazardous materials.
• Do not process media such as white spirit, butyl
alcohol and methylene chloride with the PVC pres-
sure hose. These media will destroy the pressure
hose.
and sufficient
3
Operating pressure vessels
• You must keep your pressure vessel in good work-
ing order, operate the vessel correctly, monitor the
vessel, carry out necessary maintenance and re-
pair work immediately and meet the relevant safety
precautions.
• The supervisory authority may enforce essential
control measures in individual cases.
• A pressure vessel is not allowed to be used if it
has faults or deficiencies that can endanger work-
ers or third parties.
• Check the pressure vessel for signs of rust and
damage each time before using. Do not use the
compressor with a damaged or rusty pressure ves-
sel. If you discover any damage, then please con-
tact the customer service workshop.
Do not lose these safety instructions.

6. Technical data

Mains connection
Motor rating W
Operating mode
Compressor speed
Pressure vessel capacity
(in liters)
Operating pressure
Theoretical intake capacity
(l/min)
Sound power level LWA
Uncertainty KWA
Protection type
Weight of the unit in kg
Max. altitude
(above mean sea level)
The noise emission values were measured in ac-
cordance with EN ISO 3744.
Wear hearing protection.
The effects of noise can cause a loss of hearing.

7. Before starting the equipment

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
pack aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warranty
period has expired.
230 V ~ / 50 Hz
1800
S1
2850 min
-1
100
approx. 10 bar
approx. 322
97 dB(A)
2.92 dB
IP20
51
1000 m
GB 75