Polarized Plugs - Hitachi C 10FCD Mode D'emploi Et Instructions De Securite

English
10. ALWAYS SECURE THE WORKPIECE TO THE FENCE OR THE TABLE.
to hold the w orkpiece in place. It is safer than using your hand and it frees both hands to operate the tool.
11. NEVER OVERREACH.
12. ALWAYS MAINTAIN TOOLS WITH CARE.
safest perform ance. Alw ays follo w instructions for lubricating the tool and for changing accessories.
13. ALWAYS DISCONNECT THE TOOL
14. NEVER RISK UNINTENTIONAL STARTING WHEN PLUGGING IN THE TOOL.
confirm that the switch is in the O FF position before inserting the po w er plug into the receptacle.
15. ALWAYS USE RECOMMENDED ACCESSORIES ONLY WHEN OPERATING THIS TOOL.
Consult this instruction m anual for descriptions of reco m m ended accessories. To avoid personal injuries,
use only reco m m ended accessories in conjunction with this tool.
16. NEVER STAND ON THE TOOL.
contact with the sa w blade is m ade.
17. ALWAYS CHECK FOR DAMAGED PARTS BEFORE USING THE TOOL.
guard and all other co m ponents for da m age before using the tool to assure that they will function
properly. Check all m oving parts for proper align m ent, freedo m fro m binding and other conditions that
m ig ht affect pro per o peratio n. A l w ays repair or replace an y da m aged g uards or other da m aged
co m ponents before using the tool.
18. ALWAYS CONFIRM THE ROTATION DIRECTION OF THE BLADE BEFORE USING THE
TOOL.
Alw ays feed w ork into the tool against the rotation direction of the blade in order to prevent
possible injury.
19. NEVER LEAVE THE TOOL RUNNING WHILE UNATTENDED. TURN POWER OFF.
leave tool until it co m es to a co m plete stop. Alw ays turn the po w er off w hen the tool is not in use.
Alw ays unplug the po w er cord w hen the tool is not in use.
20.
This tool w as not designed to be used for m ass-production applications and should not be used in
m ass-production environ m ents.
21.
W hen servicing this tool, use only authorized replace m ent parts.
22.
A pply 115 volts A C only to this tool. A pplying the wrong voltage or applying DC po w er can cause the
PO W ER T O OL to operate im properly and cause serious personal injury or da m age to the tool.
23.
N ever raise the sa w blade fro m the w orkpiece until it has first co m e to a co m plete stop.
24.
Alw ays use outboard stands to provide support for long w orkpieces that overhang the table of the
co m pound sa w.

25. POLARIZED PLUGS

blade is wider than the other). This plug will fit in a polarized outlet only one w ay. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any w ay.
Specific Safety Rules for Use of this Power Tool
WARNING:
The following specific operating instructions must be observed when using this POWER
TOOL in order to avoid injury:
DO's
ALWAYS OBSERVE THE FOLLOWING RULES TO ASSURE SAFE USE OF THIS TOOL:
1. Revie w this M anual and fa miliarize yourself with the safety rules and operating instructions for this
PO W ER T O OL before atte m pting to use it.
2. Alw ays confirm that the PO W ER T O OL is clean before using it.
Alw ays w ear snug-fitting clothing, non-skid footw ear (preferably with steel toes) and eye protection
3.
w hen operating the PO W ER T O OL.
Alw ays handle the PO W ER T O OL carefully. If the PO W ER T O OL falls or strikes against a hard object, it
4.
might beco m e deform ed or cracked or sustain other da m age.
5. Alw ays cease operating the sa w at once, if you notice any abnorm ality w hatsoever.
Alw ays confirm that all co m ponents are m ounted properly and securely before using the tool.
6.
4
Alw ays keep proper footing and balance w hen w orking with the tool.
before servicing and before changing blades or other accessories.
Serious injury could occur if the tool is tipped or if unintentional
To reduce the risk of electric shock, this equip m ent has a polarized plug (one
Alw ays keep tools sharp and clean for the best and
Use cla m ps or a vise
Alw ays
Alw ays check the
Do not