Intended Use; Technical Data; Before Starting The Equipment - EINHELL TE-CS 18/165 Li Traduction Du Mode D'emploi Original

3. Intended use

The cordless hand-held circular saw is designed
for sawing straight cuts in wood, wood-type
materials and plastics. When you are cutting
plastics, avoid overheating the tips of the blade as
this could melt the material.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ............................18 V
Idling speed: .............................. 4200 min
Cutting depth at 90°: ..................... 2⅛ in. 54 mm
Cutting depth at 45°: ....................1⅜ in. (35 mm)
Saw blade: ............................. Ø 6½ in. (165 mm)
Blade holder: ..............................Ø ⅝ in. (16 mm)
Blade thickness: ...........................1⁄16 in. (1.6 mm)
Weight: ......................................... 5.3 lbs (2.4 kg)
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
Anl_TE_CS_18_165_Li_USA_SPK7.indb 14 Anl_TE_CS_18_165_Li_USA_SPK7.indb 14
EN
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Setting the cutting depth (Figure 2/3)
(rpm)
-1
•
Release the handle on the rear of the guard
hood for adjusting the cutting depth (4).
•
Place the soleplate (6) flat on the surface
of the workpiece you wish to saw. Raise the
saw until the saw blade (12) is at the required
cutting depth (a).
•
Refasten the handle for adjusting the cutting
depth (4). Check that everything is securely
fastened.
5.2 Miter stop (Figure 4/5)
•
The preset standard angle between the saw
foot (6) and the saw blade (12) is 90°. You can
adjust this angle to carry out angled cuts.
•
Release the locking lever for miter setting (7)
on the front of the saw foot.
•
You can now adjust the cutting angle by up to
45°. Keep an eye on the cutting angle scale
(9) as you do so.
•
Refasten the locking screw for miter setting
(7). Check that everything is securely
fastened.
5.3 Extraction of dust and chips (Fig. 6)
•
Connect a suitable vacuum cleaner (b) to
the provided sawdust extractor connection
(14) of your circular saw (vacuum cleaner
not included). This will ensure optimum dust
extraction from the workpiece. The benefits
- 14 -
23.05.2019 11:07:26 23.05.2019 11:07:26