Publicité
8. Unpacking
• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the pack-
aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• In case of complaints the dealer must be informed
immediately. Subsequent complaints will not be ac-
cepted.
• If possible, store the packaging until the warranty
period has expired.
• Read the operating manual to make yourself familiar
with the device prior to using it.
• Only use original parts for accessories as well as for
wearing and spare parts. Spare parts are available
from your specialized dealer. Specify our part num-
bers as well as the type and year of construction of
the device in your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
9.
Attachment / Before starting the
equipment
At least two people are required to install the device.
Fix the splitter to the surface by using two screws or
two ground pegs (not included in the scope of delivery)
on the foot of the machine stand.
m WARNING: A safe stand is only guaranteed if the
base is fixed to the floor. Fixation must be ensured
at all times
9.1 Installing the base frame (fig. 3 + 4)
Your base frame is not completely assembled for pack-
aging reasons and must be mounted by yourself.
Therefore, use the hexagon screws M6 x 16 with the
nuts provided.
1.
Remove the wheel cap and dismantle the wheels.
2.
Connect all single parts of the base frame with the
machine.
3.
To do so, set up the device horizontally on the floor
and place the styrofoam padding of the packaging
under the riving knife side.
26 | GB
4.
Fit the wheels onto the wheel axles of the base
frame.
9.2 Installing the handle (4)
(enclosed accessories bag a) (fig. 5)
Fasten the handle to the U-bar with two cylindrical
screws.
9.3 Installing
(enclosed accessories bag b) (fig. 6 + 7)
1.
Fit the protective guard (L) to the trunk guide plate (5) and
use the enclosed cylindrical screws and nuts to affix it.
2.
Undo the cylindrical screw with washer that is lo-
cated on the wheel bracket.
3.
Fasten the other end of the strut to the protective
guard using the Phillips head screw and nut. (3)
4.
Now guide the open end of the strut (O) between
the washer and the wheel bracket, tighten the cy-
lindrical screw (4) again firmly.
9.4 Installing the tray table (K + M) (enclosed ac-
cessories bag c + d + e) (fig. 8 + 9 + 10)
1.
Attach the tray table (K) to the same side as the
protective guard (L). Use two cylindrical screws and
spring washers to affix the table to the log splitter. (1)
2.
Ensure that the table and the protective guard are
level in relation to each other.
3.
Undo the screw on the left of the foot.
4.
Fasten the other end of the strut to the protective
guard using the Phillips head screw and nut, align
everything and tighten the screws firmly.
5.
Now guide the open end of the strut (N) between the
screw and the foot bracket, tighten the screw slightly.
6.
Repeat the process on the other side.
7.
Align both tables in relation to each other and use
the Phillips head screws and nuts (e) to affix them.
9.5 Installing the guard (E - J)
(enclosed accessories bag f) (fig. 11 + 12)
1.
Connect the guards (H) and (I) together, use two
Phillips head screws, clamping brackets and nuts
to affix it.
2.
Fasten the guards (H, I, J) to the holes provided for
this. These are on the side of the table and the pro-
tective guard. Fasten the guard with seven Phillips
head screws, clamping brackets and nuts. Fit the
protective guard (G) to the control lever protection
(11) and use a Phillips head screw and a nut to affix it.
3.
Now fasten the guards (E + F) on the top. Fasten
them with eight Phillips head screws, clamping
brackets and nuts.
www.scheppach.com
the
protective
guard
(L)
Publicité
