Risk Assessment; Declaration Of Conformity - Respirex SPLASHMASTER CHEMPROTEX 300 Guide D'utilisation

EN: Splashmaster Chemical Protective Coverall - Instructions for Use
RESISTANCE TO PERMEATION BY CHEMICALS
Tests carried out under laboratory conditions by independent accredited laboratories in
accordance with EN ISO 6529. Table shows average breakthrough times in minutes.
Results
Chemical CHEMPROTEX
300 material
Sodium Hydroxide > 480 mins
40%
Respirex's in-house laboratory can provide permeation data against other chemicals if required.
* EN class specified by EN 14325, the higher the class number the better the performance.
REPELLENCY TO LIQUID CHEMICALS
Tests carried out under laboratory conditions by independent accredited laboratories in
accordance with EN ISO 6530.
Chemical
Sulphuric acid 30%
Sodium Hydroxide 10%
o-Xylene 99.9%
Butan-1-ol 99.9%
** EN class specified by EN 14325, the higher the class number the better the performance.
RESISTANCE TO PENETRATION BY LIQUID CHEMICALS
Tests carried out under laboratory conditions by independent accredited laboratories in
accordance with EN ISO 6530.
Chemical
Sulphuric acid 30%
Sodium Hydroxide 10%
o-Xylene 99.9%
Butan-1-ol 99.9%
‡ EN class specified by EN 14325, the higher the class number the better the performance.
PROTECTION AGAINST INFECTIVE AGENTS
Tests carried out under laboratory conditions by independent accredited laboratories.
Test Method
ISO 16603 Resistance to penetration by synthetic blood
ISO 16604 Resistance to penetration by blood-borne pathogens
ISO/DIS 22611 Resistance to penetration by biologically
contaminated aerosols
EN ISO 22612 Resistance to dry microbial penetration
EN ISO 22610 Resistance to wet microbial penetration
† EN class specified by EN 14126:2003, the higher the class number the better the
performance.
PHYSICAL PROPERTIES
Tests carried out under laboratory conditions by independent accredited laboratories.
Test Method
EN 530 Meth 2 Abrasion resistance
EN ISO 7854 Meth B Flex cracking resistance
EN ISO 7854 Meth B at -30 C Flex cracking resistance at -30
o
EN ISO 9073-4 Trapezoidal tear resistance
EN ISO 13934-1 Tensile strength
EN 863 Puncture resistance
EN ISO 13935-2 Seam strength
†† EN class specified by EN 14325, the higher the class number the better the performance.
* Seam Strength performance classification cannot be determined. Fabric tear at jaws of
instrument
WHOLE SUIT PERFORMANCE
Tests carried out under laboratory conditions by independent accredited laboratories.
Standard
EN 14605:2005+A1:2009 Type 3 Liquid jet test
EN 14605:2005+A1:2009 Type 4 Liquid spray test
Type 5 Protection against
EN 13982-1:2004+A1:2010
airborne solid particulates
EN 13034:2005+A1:2009 Type 6 Liquid spray test (mist test)
EN 14325:2004 Seam strength
EN1149-1:2006 Surface resistance (Ω)
§ EN class specified by EN 14325:2004, the higher the class number the better the
performance.
¶ EN1149-5:2018 requires a surface resistance of less than or equal to 2.5 x 10
one surface, tested
Results
Results
Kemblok™
TM
Material and
Glove
Glove Seam
> 480 mins > 480 mins
Repellency index EN Class**
> 95% 3 of 3
> 95% 3 of 3
> 90% 2 of 3
> 90% 2 of 3
Penetration index EN Class‡
< 1% 3 of 3
< 1% 3 of 3
< 1% 3 of 3
< 1% 3 of 3
Property EN Class†
Property EN Class††
C
o
Property Results
Pass
Pass
Pass
Ljmn,82/90 ≤30%,
LS,8/10 ≤15%
Pass
Class 4§
Pass ¶
Reverse, Mean
3.3 x 10
Ω, on at least
9

RISK ASSESSMENT

The summary of the risks taken into account in the design of the limited use one-piece chemical
protective coveralls.
EN 14605: 2005 +A1:2009
EN
• Full-body protective clothing with liquid-tight connections between different parts of the
Class*
clothing (Type 3: liquid-tight clothing) and with liquid-tight connections to component parts,
such as hoods, gloves, boots, visors or respiratory protective equipment, which may be
specified in other European Standards.
6 of 6
• Full-body protective clothing with spray-tight connections between different parts of the
clothing (Type 4: spray-tight clothing) and spray-tight connections to component parts, such
as hoods, gloves, boots, visors or respiratory protective equipment, which may be specified
in other European Standards.
• Partial body protection garments offering protection to specific parts of the body against
permeation of chemical liquids. Partial body protection only protects the localised parts of
the body that are covered by relevant PPE.
EN ISO13982-1:2004 +A1:2010
• The minimum requirements for chemical protective clothing resistant to penetration by
airborne solid particles, type 5 clothing.
EN 13034:2005 +A1:2009
• Chemical protective suits (Type 6) cover and protect at least the trunk and the limbs, e.g.
one-piece coveralls or two piece suits, with or without hood, boot-socks or boot-covers;
tested by the use of a reduced whole suit spray test using a variant of "EN ISO 17491-4".
EN 14126: 2003
• Requirements and test methods for re-usable and limited use protective clothing providing
protection against infective agents.
EN 1149-5: 2018
• Specifying material and design requirements for electrostatic dissipative protective
clothing, including hoods and caps, used as part of a total earthed system, to avoid
incendiary discharges, where the minimum ignition energy of an explosive atmosphere is
not less than 0,016 mJ.
SIZES
The following pictograms designate the range of height & chest sizes suitable for specific sizes
of one-piece suit, check your body measurements and select the correct size of suit. Body
measurements in cm.
CHEST
6 of 6
6 of 6
3 of 3
3 of 3

DECLARATION OF CONFORMITY

6 of 6
The declaration of conformity is available for download from www.respirex.com/DOC
EU Type Examination By:
6 of 6
1 of 6
2 of 6
EU Type Examination By:
4 of 6
3 of 6
2 of 6
*236 N
7
5
Size Height (cm)
S
M
L
HEIGHT
XL
XXL
SGS FIMKO OY
Takomotie 8
(Module B)
00380 Helsinki
FINLAND
Notified Body No. 0598
BSI Group The Netherlands B.V.
Say Building, John M. Keynesplein 9,
(Module D)
1066 EP, Amsterdam,
NETHERLANDS
Notified Body No. 2797
Chest (cm)
164-170 88-96
170-176 96-104
176-182 104-112
182-188 112-124
188-194 124-136