Yamaha RM50 Mode D'emploi page 136

9 = 1-TM internaI tom variation
10 = I-CY internaI cymbal variation
Il
=
I-PC internal percussion variation
12 = I-SE internai SE variation
13 = C-MX card mix
14
=
C-BD card kick variation
15
=
C-SD card snare variation
16
=
C-TM card tom variation
17
=
C-CY card cymbal variation
18
=
C-PC card percussion variation
19 = C-SE card SE variation
20 = W-S1 wave card slot 1
21 = W -S2 wave card slot 2
22 =
W -S3 wave card slot 3
23 = off not assigned
PARAMETER 1
PARAMETER 2 VALUE (HIGH) VALUE (LOW)
o Easy velee o Volume 0-127
1 Pan 0-64
2 Pitch 0-1 hlgh lbit 0-127 low 7 bit
3 Decay 0-1 high lmt 0-127 low 7 bit
4 Cuto« Irq 0-1 hlgh tbit 0-127 low 7 bi1
5 Balance 0-1 hlgh 1bit
0-127 low 7 bit
1 Volee com
o Namet
h'20-h'71
1 Name2 Same as above
2 Name3 Same as above
3 Name4 Same as eecve
4 Name5
Same as above
5 Name6
Same as above
6 Nama7
Same as aboya
7 Nama8
Same as above
8 Alternate 0-7
9 Output
Q-6
10 Assign
Q-3
11 Indiv iever
0-63
2 Element 1 o Wave bit 6-5 mam
00
=
preset
01
=
wave card
10
=
internai
bit 4-3 cere num
00_1,01.1,10_2
bit 0 num hlgh bit7-o num 'cw 7bit
1 PEG lëvël
bit 0 hlgh 1 bit
blt7--o low 7bit (0-144)
2 Delay pltch
bit 0 hlgh 1 bit
œr-o
-120-+120 2' comp
3 Volume 0-<13
4 Pan
0-32
5 Pltch
0-72
6 Tune
0-99
7 Reverse 0-1
8 Attack raie
0-<13
9 Decay rate 0-<13
10 Release
0-<13
11 Punch rate
0-7
12 Filler type
Q-<I
13 Culoff frq
0-127
14 Resonance
0-99
15 Fltr EG level
0-126
16 Fltr EG rate 0-63
17 Level sens
0-18 } bil3 • ,;'"
bit
18 Pitch sens
0-15 1=(-)
19 EG sens
0-15 0 _
(+)
20 Filler sens
0-15
21
LFO wave
O-<l
22 LFO sens
0-7
23 LFO speed 0-99
24 LFO delay 0-99
25 LFO select
Q-3
26 LFO Inn phase
0-<13
27 LFO mocledep 0-127
28 PEG rata
0-<13
29 1st noie sw 0-1
30 Delall time
0-127
31
Delay count 0-7
32 Delay revet
low 7bil -15-+15 2'
comp
33 Veloclly curve high 1blt 0-11
3 element 2 Same as above
MIDI DATA FORMAT
2.7.4 System Setup Parameter Change
Parameter group
=
4
PARAMETER 1
PARAMETER2 VALUE (HIGH) VALUE (LOW)
o Trigger 1 o Gain
Q-9'
1 Salf reject
Q-98
2 Noise reject Q-9
3 Cross relee! Q-9
4 Veloclty curve Q-<I
5 MIDI channel
0-1'
6 MIDI note 0-127
7 MIDI gate 1-99
8 Attenuate
0: off, 1: on
9 Speed
0: fas1, 1: slow
1 Trlgger 2 Same as steve
, ,
1
,
5 Trigger 6 seme as above
6 System o Click volee 0-22 bank Number
1 Level
0-127
2 Tempo high 1 bit low 6-0 bit (0-210)
3 Click swltch
Q-2
4 TS
O-S.
5 Monitor velodly 1-126
6 Trg chase 0-1
7 Card bank 0-1
7 MIDI
0-15 PC mode
Q-2
16 Ctrl switch 0-1
17 PUch 1-31,33-122
18 Dscay
1-31,33-122
19 Pan
1-31,33-122
20 Filler 1-31,33-122
21 Balance
1-31,33-122
22 LEO 1-31,33-122
23 Volume
1-31,33-122
24-35 Remots
0-127
36 Remota ch 0-15
37 Deviee No. 0-17
2.7.5 Program Change Table Parameter Change
Parameter group = 5
PARAMETER 1 PARAMETER2
VALUE (HIGH) VALUE (LOW)
o Program 0 o Type 0: kit, 1: volee
1 Swilch 0: on, 1: off
2 Kit 0-2 bank Number
3 Volee 0-22 bank Number
1 Program 1 Same as above
,
127 Program 127
Same as eccve
See the table at the end of this section for details.
3. Transmission
The RM50 transmirs note on and note off messages generated in
response to signale received by the trigger inputs. The note number
generated by each trigger is designated by the rhythm kit selected
for the MIDI channel specified for that trigger by the Trigger
Input 3 function. If the channel in question is not set to Rhythm
Kit channel mode, then the RM50 outputs the note number speci-
fied for the trigger by the Trigger Input 3 fonction.
Add 3