Midi Data Format - Yamaha Rm50 Mode D'emploi

MIDI DATA FORMAT
MIDI Data Format
Dev No. Deviee number
<Each
channel~$Cn
Program change
T"',
f---<IEach channel>'--T---$Bn Noteoff
L - $ 9 n Noteon/oft
1. MIDI Message
Flow
Diagrams
1.1 Reception Conditions
Program change messages are ignored.
A
program
change message selects the corresponding
voice or rhythm kit within the currently selected voice
bank (when the pitched voice channel mode is used) or
rhythm kit bank (when the rhythm kit channel mode is
used). Bank select messages (control change messages 0
and 32) can be used in combination with program
change messages to change the bank and channel mode
selectionsas well as the program.
Bach program change message selects the channel
mode, voice or rhythm kit bank, and program specified
for its program change number in the program change
table.
2.4 Aftertouch
The RM50 receives channel after touch messages; il does
Dot
re-
ceive individual aftertouch messages. Channel aftertouch mes-
sages can
he
assigned to control any of a variety of voice param-
erers, in the same manner as control change messages.
2.3 Pitch Bend
Pitch bend messages are received; however, only the most signifi-
cant data byte is valid. Pitch bend messages can he assigned to
control any of a variety of voice parameters, in the same manner
as control change messages.
2.5 Control Change
The following voice parameters can be controlled by MIDI con trol
changemessages:
Table:
Off:
Normal:
2.2 Program Change
The RM50's response to a received program change message de-
pends on the system setup program change mode setting for the
channel on which the message was received. Each channel can he
set to one of
three
prograrn change modes:
$Fa. $43,
SOn,
$7A
Single voleebulk
(LM__OO87VC)
$Fa, $43,
SOn,
$7E Internaiveee bulk
(LM__OO87VI)
~t~~~~7VWfE
Wave carel voleebulk
sec.
$43, SOn,$7E
Variation vcce bulk
(LM__0087EP)
$Fa,
$43,
SOn,
$7A
Single kit bulk
(U"'__0087KT)
seo.
$43,
$On,
$7E
Internai
kit
bulk
(lM __0087KI)
$Fe, $43, SOn, $7E
Channel setup bulk
(LM__0087ML)
$Fa, $43, $On, $7E System setup
bulk
(LM__OO87SY)
$Fe,
$43, $On,
$7E Programchangetable bulk
(LM__0087PC)
src.
$43, $On, $7E
RY30ail bulk
(LM__ OO17_-.J
sro.
$43, $On,
$7A
RYaO singlevoleebulk
(LM __OO17_.J
seo.
$7E,
sce, set
Sampledump standard
$02
$Fa, $43, $1n, $30
Parameter change
$FQ, $43, $2n Bulk dump reqeest
~o
l
- - - - - - - - - - - - - $ O n Aftertouch
DEMO
- - - - - - - - - - - - - S E n Pitch bencler
<DevNo>-r---,----
"ft
I ---------~~~ $FE
Active sensing
$Fa Timing
clock
$FA Start
$FB ContinlJll
src
Stop
Each
channel~$Bn,
$00 Bankseled
SBn, $01 Controllers
, ,
$Bn, $78
J-
$Bn, $79
Reset
ail control
NoomO
f-------,<:Each channel>-----$Cn Program change
1.2 Transmission Conditions
Activesensing
Nole on/off
Bulkdump
-------------1r
~
MIDI
CONTROL CHANGE NO. PAAAMElER
DATA RANGE
1... 31,33... 120 Volume 0...127
1... 31,33... 120 Pltch
0... 127
1... 31,33... 120
uecey
0... 127
1... 31,33... 120 Pan
0... 127
1... 31,33... 120 Fllter 0... 127
1... 31,33... 120
Balance 0... 127
1...31,33... 120
Modulation 0... 127
2. Reception
2.1 Note On/Off
Received note range:
Velocity range:
C-2-GS
1 - 127 (note on messages only)
• When more than one panel switch is assigned to a single note
number using the system setup remote switch function, the
leftmost or uppermost switch is given precedence when that
note number is received, Ali other switch assignments for the
note number are lgnored.
Add 1