General Safety Instructions - Husqvarna 540i XP Manuel D'utilisation

operator. Either of these reactions may cause you to
lose control of the saw which could result in serious
personal injury. Do not rely exclusively upon the safety
devices built into your saw. As a chain saw user, you
should take several steps to keep your cutting jobs free
from accident or injury. Kickback is the result of chain
saw misuse and/or incorrect operating procedures or
conditions and can be avoided by taking proper
precautions as given below:
• Maintain a firm grip, with thumbs and fingers
encircling the chain saw handles, with both hands
on the saw and position your body and arm to allow
you to resist kickback forces. Kickback forces can
be controlled by the operator, if proper precautions
are taken. Do not let go of the chain saw.
• Do not overreach and do not cut above shoulder
height. This helps prevent unintended tip contact
and enables better control of the chain saw in
unexpected situations.
• Only use replacement guide bars and saw chains
specified by the manufacturer. Incorrect
replacement guide bars and saw chains may cause
chain breakage and/or kickback.
• Follow the manufacturer's sharpening and
maintenance instructions for the saw chain.
Decreasing the depth gauge height can lead to
increased kickback.
SAVE THESE INSTRUCTIONS.
®
Bluetooth
CAUTION:
made to this equipment not expressly
approved by Husqvarna may void the FCC
authorization to operate this equipment.
Notice: This device complies with Part 15 of FCC
Rules and with Industry Canada licence-exempt RSS
standard. Operation is subject to the following two
conditions:
• This device may not cause harmful interference
• This device must accept any interference received,
including interference that cause undesired
operation.
Note:This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
1065 - 005 - 29.06.2020
Changes or modifications
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux
conditions suivantes:
• l'appareil ne doit pas produire de brouillage, et
• l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Suppliers Declaration of Conformity for Husqvarna
540i XP
Responsible Party
Husqvarna Professional Product, Inc.
9335 Harris Corners Parkway
Suite 500
Charlotte, NC 28269
United States
U.S. Contact Information:Michael Campbell, Sr
Director Quality Test Compliance, Telephone: +1 704
597 5000

General safety instructions

WARNING:
instructions that follow before you use the
product.
• This product is a dangerous tool if you are not
careful or if you use the product incorrectly. This
product can cause serious injury or death to the
operator or others. It is very important that you read
and understand the contents of this operator's
manual.
• Do not change the product without an approval
from the manufacturer. Do not use a product that
has been changed by others and always use
original accessories. Changes that are not
approved from the manufacturer can result in
serious injury or death to the operator or others.
Your warranty may not cover damage or liability
caused by the use of non-authorized accessories
or replacement parts.
• Long term inhalation of chain oil fumes and
sawdust can cause health problems.
Read the warning
7