Hitachi N2503AF Mode D'emploi Et Consignes De Sécurité page 5

8. STORE STAPLER PROPERLY.
When not in use, the Stapler should be stored in a dry place.
Keep out of reach of children. Lock the storage area.
9. KEEP WORK AREA CLEAN.
Cluttered areas invite injuries. Clear all work areas of unnecessary
Staplers, debris, furniture, etc.
10. NEVER USE IN PRESENCE OF FLAMMABLE
LIQUIDS OR GASES.
The Stapler produces sparks during operation. Never use the
Stapler in sites containing lacquer, paint, benzine, thinner,
gasoline, gases, adhesive agents, and other materials which are
combustible or explosive.
11. KEEP VISITORS AWAY.
Do not let visitors handle the Stapler. All visitors should be kept
away from work area.
12. DRESS PROPERLY.
Do not wear loose clothing or jewelry as they can be caught in
moving parts. Rubber gloves and nonskid footwear are
recommended when working indoors. Wear protective hair
covering to contain long hair.
13. NEVER USE NON RELIEVING COUPLER ON
STAPLER.
If a non relieving coupler is used on the Stapler, the Stapler can
remain charged with air after disconnecting and thus will be able
to drive a Staple even after disconnecting. The Stapler and air
hose must have a hose coupling such that all pressure is removed
from the Stapler when the coupling joint is disconnected.
14. CHECK PUSH LEVER BEFORE USE.
Make sure the push lever operates properly. (The push lever may
be called "safety".) Never use the Stapler unless the push lever is
operating properly., otherwise the Stapler could drive a fastener
unexpectedly,. Do not tamper with or remove the push lever,
otherwise the push lever becomes inoperable.
15. KEEP ALL SCREWS AND COVERS TIGHTLY IN
PLACE.
Keep all screws and covers tightly mounted. Check their condition
periodically. Never use the Stapler if parts are missing or
damaged.
SAFTEY
— Continued
WARNING
16. DO NOT LOAD FASTENERS WITH TRIGGER
PULLED OR PUSH LEVER DEPRESSED.
When loading fasteners into the Stapler or when connecting the
air hose,
1) do not pull the trigger;
2) do not depress the push lever; and
3) keep the Stapler pointed downward.
17.KEEP FACE, HANDS AND FEET AWAY FROM DISCHARGE AREA
DURING USE.
Never place your face, hands or feet closer than 8 inches
(200 mm) from discharge area. A serious injury can result if the
Staples are deflected by the work piece, or are driven away from
the point of entry.
18. PLACE STAPLER PROPERLY ON WORKPIECE.
Do not drive fasteners on top of other fasteners or with the
Stapler are too steep of an angle; the Staples can ricochet and
hurt someone.
19. BE CAREFUL OF DOUBLE FIRE DUE TO RECOIL.
If the push lever is unintentionally allowed to recontact the work
piece following recoil, an unwanted fastener will be driven.
In order to avoid this undesirable double fire,
1) Do not push the Stapler on the work piece with strong force;
2) Take the Stapler completely away from the work piece using
recoil, and keep the push lever away from the work piece until
the next desirable shot; and
3) Pull the trigger and release it QUICKLY when performing inter-
mittent operation.
20. DO NOT DRIVE STAPLES INTO THIN BOARDS OR NEAR COR-
NERS AND EDGES OF WORK PIECE.
The Staples can be driven through or away from the work piece
and hit someone.
21. NEVER DRIVE STAPLES FROM BOTH SIDES OF A WALL AT THE
SAME TIME.
The Staples can be driven into and through the wall and hit a
person on the opposite side.
22. CHECK FOR LIVE WIRES.
Avoid the risk of severe electrical shock by checking for live
electrical wires that may be hidden by walls, floors or ceilings.
Turn off the breaker switch to ensure there are no live wires.
23. NEVER CARRY STAPLER BY HOSE.
5
English