Use Of The Battery; Tines Replacement - Volpi OLYTECH mondial 755SP Manuel D'utilisation Et De Maintenance

6.

USE OF THE BATTERY

Codes 755SP-L-XL 845SP-L-XL
The battery is not supplied with the machine. Please make reference to the user manual of the battery
and the battery charger to get indications on the usage precautions, maintenance and charging
instructions.
Codes 855SP-L-XL 865SP-L-XL
Olive harvester Olytech Mitho 855 is supplied with lithium battery 43,2Vcc – 11,6Ah (Codes 855Sp-L-XL)
or 44Vcc 17,5Ah (Codes 865SP-L-XL) inserted in a dedicated backpack and connected either to the power
supply or to the battery charger alternatively (never simultaneously).
The machine must be used only with the original battery, to be charged using only the original battery
charger. Battery life depends on the working conditions and also on the charge status of the battery.
With full battery (100% charge), the machine can reach 4/5 hours (Codes 855Sp-L-XL) or 6/7 hours
(Codes 865SP-L-XL) of continuous work depending on the conditions of use.
In order to charge the battery, use the automatic charger 100÷240V AC, provided in the standard
equipment, connecting it to the socket and, later, to the battery connector. Connecting the electrical
outlet, a green led turns on. Connecting now the battery, the led becomes red.
The battery will be completely full only when the LED on the battery charger is green.
Charging time depends on the battery charge status. For the full charge, 4/5 hours (Codes 855Sp-L-XL)
or 5/6 hours (Codes 865SP-L-XL) are necessary. In case of need, it is occasionally possible to charge the
battery partially.
The 4 LEDs U on the battery indicate its charging status:
•
Three green leds
• Two green leds
• One green led
• One red led
Charge the battery indoor, in a fresh, dry and aired environment.
Do not disassemble, drill, warm, wet, or modify the battery and the charger.
If the machine is not used for a long time, charge the battery completely, disconnect it from the machine
and store it. Recharge the battery every 6 months. If the battery is not charged for more than 6 months,
it can be damaged and the warranty condition expire.
7.

TINES REPLACEMENT

755SP-L-XL 845SP-L-XL 855SP-L-XL 865SP-L-XL
Codes
Identify the type of tine to be replaced using the drawing E.1.
Replace tines 2D/2S. 3D/3S and 4D/4S following the procedure described in fig. E.3:
With the socket wrench R (provided) and the 2,5mm wrench K (provided), unscrew the tine's locking nut
D until the tine is free to come out from its housing P and support Y. If the tine does not come out easily,
use the tool S (included) and a hammer to push it slowly out from its housing in the direction indicated
by the arrow.
Fix the new tine in the support Y and then in the housing P, pushing it down eventually using a hammer.
Tighten the screw and the locking nut up to the limit.
Replace tines 1D/1S following the procedure in fig. E.2 and fig. E.4: move manually the tines in the
position of maximum closure, as indicated by the 2 arrows in fig. E.2 and rotate the head on itself.
In this position, from the bottom hole F, use the 3mm wrench K (provided) to unscrew the tine locking
screw until the tine is free to come out from its housing P and support Y. If the tine does not come out
easily, use the tool S (included) and a hammer to push it slowly out from its housing in the direction
indicated by the arrow.
COMPANY WITH QUALITY SYSTEM
MANAGEMENT CERTIFIED BY ICIM
– 100% battery charge
– 80% battery charge
– 50% battery charge
– 20% battery charge
Tel. +39 0376 76009 Fax +39 0376 76408 www.volpioriginale.it
= ISO 9001 =
Ref. fig. E (fig. E.1, E.2, E.3, E.4)
Davide e Luigi Volpi S.p.A.
Via San Rocco, 10 – 46040 Casalromano (MN) – Italia
42