Abicor Binzel ABITIG GRIP Mode D'emploi D'origine page 12

1 Identification
Table of contents
1 Identification
1.1 Marking
2 Safety
2.1 Designated use
2.2 Basic safety instructions
2.3 Safety instructions for electrical components
2.4 Safety instructions for welding
2.5 Safety instructions regarding protective clothing
2.6 Safety instructions for use
2.7 Classification of the warnings
2.8 Emergency information
3 Product description
3.1 Technical data
3.2 Figures used
4 Commissioning
4.1 Bending the flexible torch body (optional), Fig. 2
4.2 Preparing the welding torch for installation on the welding
power source
4.3 Setting up the welding torch, Fig. 1
4.4 Shortening the tungsten electrode
1 Identification
The TIG welding torches from the ABITIG
welding with tungsten electrodes and inert gases. The welding torches
conform to EN 60974-7 and are not considered devices that independently
1.1 Marking
This product fulfils the requirements that apply to the market to which it has
been introduced.
2 Safety
This chapter provides you with basic safety instructions and warns you
against residual hazards which must be observed in order to operate the
product safely.
2.1 Designated use
The device described in these instructions may be used only for the purpose
and in the manner described in these instructions. In doing so, observe the
operating, maintenance and servicing conditions.
Any other use is considered improper.
Unauthorized modifications or changes to enhance the performance are not
permitted.
2.2 Basic safety instructions
The product has been developed and manufactured in accordance with the
latest technology and recognized safety standards and directives. Due to
the product design, unavoidable technical residual risks exist to the user, third
parties, devices, and other material property. The manufacturer does not
accept any liability for damage caused by the non-observance of the
documentation.
► Please read the documentation carefully before using the product for the
first time and comply with the instructions contained.
► Only operate the product in technically perfect condition and ensure
compliance with all documentation.
► Read the documentation carefully before carrying out specific work, for
example, commissioning, operation, transport, and maintenance.
► Use suitable means to protect yourself and bystanders from the hazards
listed in the documentation.
► Store the documentation within easy reach of the device for reference
and enclose all documents when passing on the product.
EN - 4
EN-4
EN-4
EN-4
EN-4
EN-4
EN-5
EN-5
EN-5
EN-5
EN-5
EN-5
EN-6
EN-6
EN-6
EN-7
EN-7
EN-7
EN-7
EN-7
®
GRIP series are used for inert gas
®
ABITIG
4.5 Sharpening tungsten electrodes, Fig. 3
4.6 Connecting the cable assembly
4.7 Connecting the coolant hoses
4.8 Bleeding the coolant circuit
4.9 Connecting the shielding gas and setting the gas volume
5 Operation
5.1 Handle operating elements
5.2 Replacing the torch neck, Fig. 5
5.2.1 Inserting a plug to block residual coolant and dirt, Fig. 6
5.3 Welding
6 Decommissioning
7 Maintenance and cleaning
7.1 Cleaning the welding torch
7.2 Annual maintenance by an electrician
7.3 Replacing wear parts, Fig. 4
8 Disposal
9 Warranty
fulfil functions.
Arc welding can only be carried out in connection with a welding power
source.
A corresponding marking has been affixed to the product, if required.
Non-observance of the safety instructions may result in risks to the life or
health of personnel and result in environmental damage or material damage.
► Do not exceed the maximum load data specified in the documentation.
Excessive loads lead to irreparable damage.
► Do not make any structural modifications to the product.
► During welding work outdoors, use suitable protection against the
weather conditions.
► Consult the documentation on additional welding components.
► When handling gas cylinders, consult the instructions from the gas
manufacturers and the corresponding local regulations, e.g. pressurised
gas regulations.
► Observe the local accident prevention regulations.
► Only trained specialists should commission, operate, and service the
device. Qualified personnel are persons who, based on their special
training, knowledge, experience and due to their knowledge of the
relevant standards, are able to assess the tasks assigned to them and
identify possible dangers.
► Ensure the work area is well lit and keep it in good order.
► For the entire duration of servicing, maintenance and repair work, switch
off the welding power source and the gas and compressed air supplies,
and disconnect the mains plug.
► For disposal, observe the local regulations, laws, provisions, standards,
and directives.
®
GRIP, ABITIG GRIP AT/WT
EN-7
EN-7
EN-8
EN-8
EN-8
EN-8
EN-8
EN-8
EN-8
EN-8
EN-9
EN-9
EN-9
EN-9
EN-9
EN-10
EN-10