Publicité
Les langues disponibles
Les langues disponibles
19. Check damaged parts
Before further use of the tool, a guard or other
part that is damaged should be carefully checked
to determine that it will operate properly and per-
form its intended function. Check for alignment of
moving parts, binding of moving parts, breakage
of parts, mounting, and any other conditions that
may affect its operation. A guard or other part
that is damaged should be properly repaired or
replaced by an authorized service center unless
otherwise indicated elsewhere in this instructions
manual. Have defective switches replaced by
an authorized service center. Do not use tool if
switch does not turn it on and off .
20. Warning
The use of any other accessory or attachment
other than recommended it this operating instruc-
tion or the catalog may present a risk of personal
injury.
21. Have your tool repared by an expert
This electric appliance is in accordance with the
relevant safety rules repairing of electric appli-
ances may be carried out only by experts oth-
erwise it may cause considerable danger for the
user.
22. Connect the dust extraction device
Wherever there are facilities for fitting a dust ex-
traction system, make sure it is connected and
used.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
Special safety information
Caution! This tile cutting machine is designed for wet
cutting only. The machine may be operated only with
a non-segmented diamond cutting wheel.
• Wet hands: Never touch the electrical components
of the machine (e.g. switches) with wet hands.
• Plug-in connections: All plug-in connections must
be located in a dry place and must not lie on the
floor.
• Cooling the cutting wheel: Make sure that the cut-
ting wheel is cooled with water during the complete
cutting process.
• Dry cutting: Never carry out dry cuts with cutting
wheels designed for wet cutting.
• Dust protection: Always wear a protective dust
mask when cutting tiles.
• Diamond cutting wheels: Do not feed the tile into
the machine any faster than the cutting wheel can
cut.
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
• Use only cutting wheels which are designed for a
minimum speed of 3000 min-1.
• Selecting the cutting wheel Select the diamond
cutting wheel to suit the material you want to cut.
• Fitting the cutting wheel: Before you install the cut-
ting wheel, check the spindle, the spindle nut and
the flanges for damage, wear or a loose fit. Re-
place damaged or worn parts without delay.
• Direction of rotation of the cutting wheel: Check
the direction arrow on the cutting wheel; the arrow
must point in the same direction as the direction in
which the motor shaft rotates.
• Cutting wheel spindle: Make sure that the diameter
of the hole in the cutting wheel is the same as the di-
ameter of the cutting wheel spindle on the machine.
• Cutting wheel guard: Only use the tile cutting ma-
chine with a properly fitted and adjusted cutting
wheel guard.
• Cutting wheel speed: Do not exceed the safe oper-
ating speed of the cutting wheel.
• Sanding/grinding with the cutting wheel Do not try
to use the cutting wheel for sanding or grinding
jobs, e.g. to sand/grind the edge of a cut tile. Al-
so, do not use the machine for radius cuts or round
cuts. This tile cutting machine is suitable only for
household use.
• Cutting wheel stop time: After the machine has
been switched off, the cutting wheel needs 40 sec-
onds to come to a standstill. Wait until the cutting
wheel has stopped completely, pull the power plug
out of the socket outlet, and only then touch the
cutting wheel if necessary.
• Avoid all contact with the rotating cutting wheel
when the machine is in operation.
• The electric tool must never be used without the
PRCD plug supplied with it.
• Keep water away from electrical parts of the tool
and from persons in the work area!
• If the power plug or the power cable are damaged
they must be replaced either by the manufacturer
or by a service company authorized by the manu-
facturer.
• To comply with the requirements imposed by the
safety regulations, all technical modifications
which change the equipment's characteristics (e.g.
speed) must be left strictly to the manufacturer.
• Keep this safety information in a safe place.
Special safety instructions for stone cutting ma-
chines
• Place the stone cutting machine on a level work
surface with stable footing before using it. Ensure
that there is sufficient room for freedom of move-
ment.
• In order to avoid a dust hazard, the machine may
only be used in the wet area. This is also mandato-
ry because the diamond cutting wheel is only suit-
able for wet cutting.
GB | 27
Publicité
