Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GIS 1000 C Professional Notice Originale

OBJ_BUCH-2270-005.book Page 30 Wednesday, September 21, 2016 5:29 PM
30 | English
Definitions
Infrared heat radiation
Infrared heat radiation is electromagnetic radiation emitted
by every body. The amount of radiation depends on the tem-
perature and the emissivity degree of the body.
Emissivity Degree
The emissivity degree of an object depends on the material
and the structure of its surface. It states how much infrared
heat radiation the object emits compared to an ideal heat
emitter (black body, emissivity degree  = 1).
Thermal Bridge
A thermal bridge is an object that undesirably transmits heat
outwards or inwards, therefore differing significantly from the
temperature of the rest of a wall or from the desired tempera-
ture of a wall.
As the surface temperature at thermal bridges is lower than in
the rest of the room, the risk of mould increases significantly
at these locations.
Relative Humidity
The relative humidity provides information on how intensive
the air is saturated with water vapour. It is stated as a percent-
age of the maximum amount of water vapour that the air can
absorb. The maximum amount of water vapour depends on
the temperature: The higher the temperature, the more
amount of water vapour the air can absorb.
When the relative humidity is too high, the risk of mould in-
creases. Too low humidity can lead to health impairments.
Dew Point Temperature
The dew point temperature indicates the temperature at
which the water vapour in the air starts to condense. The dew
point temperature depends on the relative humidity and the
air temperature.
When the temperature of a surface is below the dew point
temperature, water begins to condense on this surface. The
larger the difference of both temperatures and the higher the
relative humidity, the greater the condensation.
Condensate on surfaces is a major cause for the formation of
mould.

Maintenance and Service

Maintenance and Cleaning

Store and transport the measuring tool only in a suitable con-
tainer such as the original packaging or the protective pouch
(accessory). Do not, as an example, store the measuring tool
in a plastic bag, as the evaporation could damage the humidi-
ty and temperature sensor 5. Do not affix any stickers near to
the sensor on the measuring tool.
Do not store the measuring tool for long periods out of a hu-
midity range between 30 to 50 %. When the measuring tool is
stored too moist or too dry, faulty measurements can occur
when starting operation.
Keep the measuring tool clean at all times.
1 609 92A 211 | (21.9.16)
Wipe off debris using a moist and soft cloth. Do not use any
cleaning agents or solvents.
When cleaning, fluids should not penetrate into the measur-
ing tool.
Be very careful especially when cleaning humidity and ambi-
ent temperature sensor 5, the camera 22, the reception lens
23, the light 24 and the laser beam exit openings 2:
Ensure that there is no lint on the camera, the reception lens
or the laser beam exit openings. Clean the camera, the recep-
tion lens and the laser beam exit openings only with cleaning
agents also suitable for camera lenses. Do not attempt to re-
move dirt from the sensor, camera or reception lens using
pointed objects, and do not wipe over the camera and recep-
tion lens (risk of scratching).
If the event of a repair, send in the measuring tool in the origi-
nal packaging or in the protective pouch (accessory).
If you want your measuring tool to be calibrated again, please
contact a Bosch service centre (see "After-sales Service and
Application Service").

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the type plate of
the measuring tool.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Bosch Power Tools