Power Supply - Bosch GIS 1000 C Professional Notice Originale

OBJ_BUCH-2270-005.book Page 22 Wednesday, September 21, 2016 5:29 PM
22 | English
1) at an ambient temperature of 20–23 °C and an emissivity degree of >0.999
2) Information according to VDI/VDE 3511 Page 4.3 (publication date: July 2005); applies for 90 % of the measuring signal.
Deviations of the measuring results are possible in all ranges beyond the indicated dimensions in the Technical Data.
3) Refers to infrared measurement, see graphic:
4) For Bluetooth® low energy devices, establishing a connection may not be possible, depending on model and operating system. Bluetooth® devices
must support the SPP profile.
5) limited performance at temperatures <0 °C
Technical data determined with battery from delivery scope.
The measuring tool can be clearly identified with the serial number 6 on the type plate.
Assembly

Power Supply

The measuring tool can either be operated with commercially
available batteries or with a Bosch lithium-ion battery pack.
Article number 3 601 K83 370: The measuring tool can be
operated only with conventional batteries.
Operation with Batteries
(not for article number 3 601 K83 370) (see figure A)
The batteries are inserted into the battery adapter.
 The non-rechargeable battery adapter is intended only
for use in designated Bosch measuring tools and must
not be used with power tools.
To insert the batteries, slide the cover 27 of the battery
adapter into the battery port 29. Place the batteries in the
cover as per the illustration on the sealing cap 28. Slide the
sealing cap over the cover until you feel it engage and it is flush
with the handle of the measuring tool.
To remove the batteries, press the unlocking but-
tons 3 of the sealing cap 28 and pull off the sealing
cap. Take care that the batteries do not fall out. To
do so, hold the measuring tool with the battery
port 29 facing upward. Remove the batteries. To
remove the inside cover 27 from the battery port
29, reach into the cover and pull it out of the measuring tool
by applying light pressure to the side wall.
Always replace all batteries at the same time. Only use batter-
ies from one brand and with the identical capacity.
 Remove the batteries from the measuring tool when
not using it for extended periods. When storing for ex-
tended periods, the batteries can corrode and self-dis-
charge.
1 609 92A 211 | (21.9.16)
1 m 2 m
Operation with Battery Pack
(not for article number 3 601 K83 370) (see figure B)
Note: Use of battery packs not suitable for the measuring tool
can lead to malfunctions of or cause damage to the measuring
tool.
Note: The battery pack is supplied partially charged. To ensure
full capacity of the battery pack, completely charge the battery
pack in the battery charger before using for the first time.
 Use only the chargers listed in the technical data. Only
these battery chargers are matched to the lithium-ion bat-
tery of your measuring tool.
The lithium-ion battery pack can be charged at any time with-
out reducing its service life. Interrupting the charging proce-
dure does not damage the battery pack.
 Following the automatic shut off of the measuring tool,
do not continue to press the On/Off button. The battery
can be damaged.
To insert the charged battery pack 30, slide it into the battery
port 29 until you feel it engage and it is flush with the handle
of the measuring tool.
To remove the battery pack 30, press the unlocking buttons
3 and pull the battery pack out of the battery port 29. Do not
exert any force.
Operation with Batteries (3 601 K83 370) (see figure C)
To open the battery lid 31, press the unlocking buttons 3 and
remove the battery lid.
Make sure that you insert the batteries at the correct polarity
according to the illustration on the battery lid.
Mount the battery lid 31 again until you feel it engage.
Always replace all batteries at the same time. Only use batter-
ies from one brand and with the identical capacity.
 Remove the batteries from the measuring tool when
not using it for extended periods. When storing for ex-
tended periods, the batteries can corrode and self-dis-
charge.
5 m
Bosch Power Tools