Worx WG190 Mode D'emploi page 12

line will not feed properly and will result in
improper cutting head function or can cause
serious injury. Do not use other material such
as wire, string, rope, etc. Wire can break off
during cutting and become a dangerous
projectile that can cause serious injury.
Trimming
Postion the trimmer head as shown in Fig. G1
for trimming.
Keep the bottom of the trimmer head just
above the ground and at an angle. Allow only
the tip of line to make contact. Do not force
trimmer line into work area.
Edging (See Fig. G1, G2, G3, G4)
AlwAyS REmoVE THE BATTERy
PACk BEFoRE AdJuSTiNG THE
TRimmER HEAd PoSiTioN.
For edging, position the trimmer head as Fig.G2.
To rotate the trimmer head to edging—first
hold the trimmer shaft as shown in Fig G3---
then with your other hand hold the trimmer
head - Push down and rotate 180 degrees and
then release- the trimmer will then lock into
12
the edging position automatically—Fig G4
NoTE: The trimmer head will only rotate in
one direction. While rotating, please remove
the battery from your tool for your safety.
The edge guide helps protect the unit and
keeps the unit from contacting the ground.
Take extra caution while edging as objects can
be thrown from the trimmer line.
AuTomATiC liNE FEEd SySTEm
When initially switching ON the trimmer, a
small length of line is fed out.
A 'clattering' noise will be heard when
the lines hit the line cutter. do NoT BE
AlARmEd, this is normal. After a few
seconds the line will be cut to the correct
length and the noise will reduce as the motor
receives full speed.
If the noise of the line being cut can't be heard,
more line will need to be fed out.
To feed more line, it is first necessary to allow
the trimmer to stop completely, then restart,
allowing the motor to reach full speed.
Repeat above until you hear the lines hitting
against the line cutter.
13 Grass Trimmer/Edger
"
To mANuAlly FEEd THE liNE
(See Fig. H1)
AlwAyS REmoVE THE BATTERy
PACk BEFoRE AdJuSTiNG THE
TRimmER HEAd PoSiTioN.
If required, line can be feed out manually
To operate, press and release manual line feed
button (15), while gently pulling out the line
until it is long enough to reach the line cutter.
If the line extends past the line cutter, too
much line has been fed out.
If too much line is fed out, remove the spool
cap and turn spool counter-clockwise until the
line is at the desired length.
To REmoVE THE CAP (See Fig. H2)
• Press and hold the two latches (11).
• Pull cap away from the spool holder
• When refitting the spool cap, keep all areas
of the cap and spool holder clean.
• Replace the cap, pressing firmly down
towards the spool holder to ensure cap is fully
located into position.
• Check that the cap is correctly fitted by trying
to remove it without depressing the two
latches.
REPlACE THE TRimmER liNE ANd
SPool (See Fig. i).
AlwAyS REmoVE THE BATTERy
PACk BEFoRE AdJuSTiNG THE
TRimmER HEAd PoSiTioN.
• Remove Spool Cap Cover.
• For your convenience it is recommended you
buy replacement spools with the trimmer line
preinstalled.
• Remove the old Spool from Spool Holder.
Clear any broken line or cutting debris from
the spool area.
• Pull the line from the new replacement Spool
through the eyelet of the Spool Holder.
• Place new Spool into the holder with the cut
out areas of the Spool facing inward or down.
When installed into the Spool Holder, the
smooth side of the Spool should be visible.
• Release line from cleat on the Spool.
• Refit the Spool Cap Cover.
EN