Menu 3. Select Language; Menu 4. Stand-By Mode; Menu 5 - Sound Mode; Menu 6. Initial Load - Bio Bronpi HYDRO Série Instructions D'installation, D'utilisation Et D'entretien

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 43
Programme 3: Monday (OFF), Tuesday (ON), Wednesday (ON),
Thursday (ON), Friday (ON), Saturday (ON), and Sunday (OFF.)
Programme 4: Monday (ON), Tuesday (ON), Wednesday (OFF),
Thursday (OFF), Friday (OFF), Saturday (OFF), and Sunday (ON.)
Thanks to this type of setting we can combine 4 different times
throughout the days of the week, but always keeping in mind not to
superimpose or intermesh the times.
Sub-menu 02-04- Weekend Programme
In the same way as in the daily programme, this setting up has two independent times to start and two to stop, with the precision that it only
applies to Saturday and Sunday. To access this setting up we need
to start from the following screen (see drawing D44):
We need to confirm the access to this programme by pressing
button no.3 "SET" and it should show the following screen (see
drawing D45):
We modify the value "OFF" and select "ON": Finally, we introduce the
times to start and stop in order to complete the desired setting up.
As in the daily programme, if we need to set up only one time to start and stop, the options START 2 and STOP 2 should indicate "OFF."
It is also possible to schedule one automatic start hour and manual stop hour (or vice versa).
Example:
START 1: 00:1 hours and STOP 08: "off"
or
START 1: "off" and STOP 1: 22:00 hours.
9.4.4

MENU 3. SELECT LANGUAGE

It allows selecting the languages among those available. To access
to this menu you have to confirm with button nº 3 "SET" and then,
choose the selected language among those available: Spanish, English, French, Italian, German and Portuguese with buttons nº 1 and 2
(see drawing D46).
9.4.5

MENU 4. STAND-BY MODE

In case of thermo-stoves, once the ambient or water temperature
reaches the temperature set plus a differential (2º C) by the user
and it is activated "stand-by mode" the thermo-stove will be
automatically turned off. When the ambient temperature falls to
the set temperature minus a differential (2ºC) the thermo-stove
automatically restarts an ignition cycle. It means that if you choose
an ambient temperature of 22ºC the thermo-stove will turn-off when the room temperature is 24º C and it will restart automatically when the
ambient temperature falls to 20ºC, independently of the water temperature.
In case of the "Stand-by Mode" is deactivated (by default) the
thermo-stove will work by modulating the power when it reaches
one of both temperatures, that allows the temperature set could be
higher.
9.4.6

MENU 5 - SOUND MODE

By activating this mode, the thermo-stove will emit a sound when the
system detects a fault and goes into the alarm state. To access to
this menu you have to confirm with button nº 3 "SET" and then, choose "on" with buttons nº 1 and 2 (see drawing D48).
9.4.7

MENU 6. INITIAL LOAD

In case of the thermo-stove has run out of fuel during the operation,
in order to avoid an anomaly in the next ignition, it is possible to
carry out a fuel pre-load for a maximum time of 90 seconds to
load the auger feeder. This can be used when the thermo-stove is
switched off and cold. To start the pre-load press button nº 2 and to
stop it press button nº 4 (see drawing D49).
It is very important that the burner is totally empty when you start the thermo-stove. So, when the initial pre-load is finished, you
must check the burner is clear of fuel in order to achieve correct ignition of the thermo-stove.
9.4.8

MENU 7- STOVE STATE

It shows the current state of the thermo-stove and
provides information about the devices connected.
Therefore, the user can get some technical information.
The next screens are seen automatically (see drawings
D50, D51, D52 and D53).
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS
M-2-4
PROGRAMME
WEEKEND
Off
M-2-4-01
PROGRAMME
WEEKEND
Menu 04
SPA
On
Menu 04
STAND-BY
MODE
On
Menu 05
SOUND
MODE
77"
22ºC
LOAD
INITIAL
TIME 1
REMAINING TIME INTERMEDIATE CLEANING
STATE
STATE
ALARM DELAY
36
28ºC
D50
OPERATIONAL STATE
HYDRO SERIES
D44
D45
D46
D47
D48
D49

Publicité

Table des Matières
loading

Table des Matières