Correction Of Malfunctions; After-Sales Service And Application Service - Bosch GAS 15 Professional Notice Originale

OBJ_BUCH-3290-001.book Page 19 Thursday, July 13, 2017 9:41 AM
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Removing/Changing the Filter (see figures H1–H2)
Replace a damaged pleated filter immediately.
– Unlock the latches 9 and remove the vacuum lid 8.
– Turn the filter holder 29 all the way in direction of rotation
" " and take the filter holder together with the filter 20
out of the container 1.
– Pull the dirty/damaged filter 20 off the filter holder 29.
– Brush down the flaps of the filter with a soft brush.
or
Replace a damaged filter.
– Attach the filter holder 29 to the cleaned/new filter 20.
– Put the filter holder 29 together with the filter 20 over the
filter basket 30 and turn the filter holder 29 all the way in
direction of rotation " ".

Correction of Malfunctions

Problem
The vacuum turbine does not start.
Vacuum turbine switches off.
Vacuum turbine does not restart after emptying
the container.
Vacuuming power decreases.
Dust escapes during vacuuming
The automatic shut-off (wet vacuuming) does
not respond.
Filter cleaning inoperative.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
Bosch Power Tools
– Reattach the vacuum lid 8 again and lock the latches 9.
Container
– Wipe out the container 1 from time to time with a commer-
cially available, non-scouring cleaning agent and allow to
dry.
Storage and Transport (see figure I)
– Wrap the power cable around the carrying handle 6.
– Insert the vacuum tubes 26 into the holders 12.
– Put the vacuum hose 17 around the vacuum lid and hang
the retaining strap 16 on the holder 11.
– Carry the vacuum cleaner only by the carrying handle 6.
– Store the vacuum cleaner in a dry room and secure it
against unauthorised use.
– To lock the castors 10, actuate the castor brakes 14 by
pushing down.
Corrective Measure
– Check the mains cable, mains plug, fuse and socket.
GAS 15 PS:
Mode selector switch 4 set to "Start/Stop automatic".
– Set mode selector switch 4 to the "vacuum" symbol and switch the power
tool connected to the socket outlet 3 on.
– Empty container 1.
– Switch vacuum cleaner off and wait 5 seconds; switch on again after 5 sec-
onds.
– Remove any blockages from the vacuum nozzle, vacuum tube 26, vacuum
hose 17 or filter 20.
– Change the plastic bag 19 or dust bag.
– Properly engage the filter holder 29.
– Mount vacuum cleaner lid 8 properly and lock latches 9.
– Change the filter 20.
– Check that the filter 20 has been installed correctly.
– Change the filter 20.
The automatic shut-off does not function with non-conductive liquids or
foam/bubbles.
– Monitor the level continuously.
– Press the SFC switch 7.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
English | 19
1 609 92A 40A | (13.7.17)