Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
Additional Safety Rules for Sawing in Table Saw
Mode
• Never cut when riving knife and/or top guard are removed.
WARNING! The design does not allow the use as bench saw
as long as the U-shaped guard is not mounted.
• Always use the push stick. Never cut workpiece smaller than 30 mm.
• Without additional support the machine is designed to accept the
maximum workpiece size of:
– Height 50 mm by width 400 mm by length 500 mm.
– Greater workpiece needs to be supported by suitable additional
table.
• Always adjust the sliding fence correctly to avoid contact with the lower
guard.
• Do not use saw blades with a body thickness greater or a width of
tooth smaller than the thickness of the riving knife.
• Ensure that the table is securely fixed.
• Always keep the push stick (58) in its place when not in use (fig. A2).
• Replace the table insert when worn.
• Slotting, rebating or grooving is not allowed.
• During transportation make sure that the upper part of the saw blade is
covered, e.g. by the guard.
• Do not use the guard for handling or transportation.
• Do not remove the saw bench table when adjusting the riving knife.
Mitre Saw Mode
• Ensure that the upper portion of the saw blade is completely enclosed
in the mitre sawing mode. Never remove the upper blade guard when
using the machine in mitre saw mode.
• Never cut workpiece shorter than 20 mm.
• Without additional support the machine is designed to accept the
maximum workpiece size of:
– Height 40 mm by width 140 mm by length 400 mm
– Longer workpieces need to be supported by suitable additional
table.
• Always clamp the workpiece safely.
• When performing vertical straight cross-cuts, adjust the sliding fence
correctly to ensure a clearance of max. 5 mm between the saw blade
and the fence (fig. O).
• When performing mitre, bevel or compound mitre cuts, adjust the
sliding fence to ensure the correct clearance for the application (fig. P).
• Ensure that the upper portion of the saw blade is completely enclosed
in the mitre sawing mode.
• Refrain from removing any cut-offs or other parts of the workpiece from
the cutting area while the saw is running and the saw head is not in the
rest position.
Residual Risks
The following risks are inherent to the use of saws:
– injuries caused by touching the rotating parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot
be avoided.
These are:
– Impairment of hearing.
The following factors are of influence to noise production:
~ the material to be cut;
~ the type of saw blade;
~ the feed force.
– Risk of accidents caused by the uncovered parts of the rotating saw
blade.
– Risk of injury when changing the blade.
– Risk of squeezing fingers when opening the guards.
– Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.
26
All manuals and user guides at all-guides.com
The following factors are of influence to dust exposure:
– worn saw blade;
– dust extractor with air velocity less than 20 m/s;
– workpiece not exactly guided;
– Insufficient dust extraction caused by uncleaned exhaust filters.
Markings on Tool
The following pictograms are shown on the tool:
DATE CODE POSITION (FIG M)
The Date Code (59), which also includes the year of manufacture, is printed
into the housing.
Example:
Package Contents
The package contains:
1 Assembled table top mitre saw
1 Parallel rip fence
1 Guard for bench saw position
1 Bottom guard for bench saw position
1 Push stick
1 Hex key 4/6 mm
1 Hex key 5 mm
1 Two-pin spanner
1 Dust extraction adapter for top guard
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may
• Take the time to thoroughly read and understand this manual prior to
Description (fi g. A1–A5)
A1
1 On/off switch
2 Head lock up release lever
3 Additional saw bench table locking knob
4 Moveable lower blade guard
5 Fixed table
Read the instruction manual before use.
When using the machine in the mitre saw mode,
make sure that the upper part of the saw blade is
fully covered by the upper saw blade guard.
Only use the machine when the bench saw table is in
highest position.
When using the machine in the bench saw mode,
make sure that the upper and lower guards are in
place. Only use the machine when the bench saw
table is in horizontal position.
Carrying point.
NEVER use the machine in table saw mode when
upper saw blade guard and fixed lower guard are not
mounted.
2010 XX XX
Year of Manufacture
have occurred during transport.
operation.
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Publicité
