Important; General Characteristics; Electrical Connection Diagram - Astralpool NF Série Manuel D'installation Et D'entretien

ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be implemented for
installation and start-up. Therefore, the installer as well as the user must read the instructions before beginning installation and start-up.
Keep this manual for future reference.
To achieve optimum performance of the NF Floodlamp follow the instructions provided below:
1. VERIFY THE CONTENTS OF THE PACKING:
The following accessories are included inside the box:
Panelled pool floodlamp:
Housing body
Floodlamp unit
Watertight joint
Clamp
Bag of screws
Installation and maintenance manual

2. GENERAL CHARACTERISTICS:

This floodlamp has been designed to be used fully submerged underwater in fresh water swimming pools. It is a Class III electric apparatus with
very low safety voltage (12V with alternating current).
The floodlamp complies with IPX8 degree of protection (resistance to penetration of dust, solid bodies and humidity) at a nominal immersion
depth of 2 m.
This floodlamp complies with international safety standards for lights, especially the EN 60598-2-18 standard. LIGHTS PART 2: SPECIFIC
REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric components which have been
inserted or handled at locations other than its own premises.
3. INSTALLATION:
•
Never install in vertical position with the lamp facing downwards.
•
In order to clearly light a pool it is recommended lo install a floodlamp every 25 m² of water surface.
•
In order to prevent glare, the floodlamps should be installed so that they face away from the residence or usual view of the swimming pool.
•
In the event that lighting is used in training or competition pools, the floodlamps should be installed on the sides to prevent glare on the
swimmers.
•
To avoid the need to empty the pool to change the lamp, we recommend that the floodlamp be installed in areas which are accessible from
the upper edge of the pool, at approximately 400-700 mm from the water surface (Fig. 1).
Prior to installation verify that the gland seal (no. 13) has been fully tightened.
The method of fastening the housing to the pool wall varies depending on whether it is a floodlamp for concrete pools, prefabricated pools or
panelled swimming pool.
Panelled swimming pool with Liner
The projector can be installed in a metal sheet or plastic panelled swimming pool, using the template, and making a circular hole of 277 mm.
diameter and 8 holes ∅ 4 mm (Fig. 6).
Place the recess (no. 23) (The housing incorporates the joint that carries out the water tightness), through the inside of the pool and bolt the 8
DIN 7982 4.8x25 screws (no. 22) (fig. 7). Make sure that the cable outlet from the recess is on the upper side.
Place the liner.
Place the clamp (no. 20) through the inside of the pool, fasten it to the recess (no. 23) with 16 screws.
Cut the Liner which is inside the clamp, so that the recess is free and proceed to assemble the projector.
4. ASSEMBLY:
After installation of the housing and the clamp, if it is a prefabricated swimming pool, assemble the floodlamp.
To connect the floodlamp to the electric power supply insert the cable through the gland seal nut (no. 13). Tighten the gland seal nut until you
can verify that the cable will not yield when you pull on it with your hand.
Take the precaution of leaving 1.5 m of cable wound on the base of the floodlamp (no. 9) in order to be able to remove the floodlamp to the
edge of the pool in the event that lamp replacement or handling is required (Fig. 1).
Before introducing the ensemble of the projector in the housing (Fig. 8), check that both of the screws (n. 1) are in the position OPEN. If it is
so, introduce the projector ensemble to the housing. To obtain a good illumination of the swimming pool it is important that the anagram of the
decorative ring (n. 2) remains situated at the top (Fig. 8).
Turning the two screws (no. 1), the slot has to remain in vertical position (Fig. 9).
5. CONTROL SYSTEMS OF THE LED LAMP:
The LED lamp can be controlled in two different ways: either by a normally closed pushbutton or by means of the receiver and/or remote control
In both cases, you should make sure that the voltage received by the lamp is never more than 12V.
The lamp should only be operated underwater and anchored to the vertical walls of the pool. The lamp is supplied with heat protection, which in
the event of excess temperature reduces the lighting level to avoid overheating.
5.1. COLORPLUS ECO: pushbutton control
The system has 14 operation modes: 7 set colours and 7 sequences of different colours (see section 5.1.2.) The colour or sequence is changed
by a quick press of the pushbutton. The lamp/s is/are placed in white if the pushbutton is pressed for longer.

5.1.1. Electrical connection diagram

The COLORPLUS ECO system is composed of the projector/s, the transformer and the normally closed (NC) pushbutton.
2