Important; General Characteristics; Installation Par 56 Rgb 1.11 Wireless Lamp; Assembly Par 56 Rgb 1.11 Wireless Lamp - Astralpool LUMIPLUS PAR56 RGB 1.11 WIRELESS Manuel D'installation Et D'entretien

ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be
implemented for installation and start-up. Therefore, the installer as well as the user must read the instructions
before beginning installation and start-up.
Keep this manual for future reference.
To achieve optimum performance of the Underwater LumiPlus PAR 56 RGB 1.11 Wireless Lamp, follow the instructions
provided below:
1. VERIFY THE CONTENTS OF THE PACKING:
59126
1 PAR56 RGB1.11 Wireless
Lamp + 1 LumiPlus Control
Motion
nstallation and mainte-
I
nance manual
Bag of fastenings
Warranty booklet

2. GENERAL CHARACTERISTICS:

This lamp has been designed to be used fully submerged in fresh water. It is a Class III electric apparatus with very
low safety voltage (12 V with alternating current). The lamp is class 116, in accordance with standard EN 50065.
The floodlamp complies with IPX8 degree of protection at a nominal immersion depth of 2 m.
This floodlamp complies with international safety standards for lights, especially the EN 60598-2-18 standard: LIGHTS
PART 2: SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
LumiPlus Control Motion must not be washed or immersed in water.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric compo-
nents which have been inserted or handled at locations other than its own premises.

3. INSTALLATION PAR 56 RGB 1.11 WIRELESS LAMP:

• To correctly light a swimming pool we recommend install a lamp in the range LumiPlus 1.11 every 20 m² of water
surface. Recommendation valid for light coloured pools. In darker coloured pools or stainless steel pools we recom-
mend oversizing the proportion of lamps per m².
• The connection boxes should be at least 2 m. from the edge of the swimming pool or water installation.
• The 230/12V transformer supplying the lamp, should be installed 3.5 m. from the edge of the swimming pool or
water installation.
• Conduits installed less than 3.5 m. from the swimming pool edge, should not be lined or covered in metal.
THE HOLES AT THE BACK OF THE LAMP (FIG. 1) SHOULD BE LEFT FREE WHEN ASSEMBLING THE PROJECTOR,
SO THAT WATER CAN FLOW INSIDE FOR OPTIMUM PERFORMANCE OF THE LAMP.

4. ASSEMBLY PAR 56 RGB 1.11 WIRELESS LAMP:

Follow these steps to assemble the PAR56 LED lamp (59126 ,59127) in an underwater projector with an incandescent
lamp:
1. Ensure that the lamp is NOT receiving voltage.
2. Remove the lamp unit and the part of the projector and place it on the edge of the swimming pool (this operation is
fully described in the projector manual) (Fig. 2).
3. Dismantle the parts of the projector required to remove the incandescent lamp (this operation is fully described in
the projector manual)(Fig. 3).
4. Loosen the two screws which electrically connect the PAR56 incandescent lamp (Fig. 4).
5. Place the PAR 56 LED lamp electrically connecting it with the two connection screws (Fig. 5).
6. Assemble the projector in its initial position (this operation is fully described in the projector manual).
7. Connect the projector to the mains.
59127
2 PAR56 RGB 1.11 Wireless
Lamps + 1 LumiPlus Control
Motion
nstallation and mainte-
I
nance manual
Bag of fastenings
Warranty booklet
ATTENTION
59128
1 RGB 1.11 Global Wireless
projector+ 1 LumiPlus
Control Motion
nstallation and mainte-
I
nance manual
Bag of fastenings
Warranty booklet
3
59129
2 RGB 1.11 Global Wireless
Projectors + 1 LumiPlus
Control Motion
nstallation and mainte-
I
nance manual
Bag of fastenings
Warranty booklet