DeWalt DW738 Mode D'emploi page 21

• Insert one hex bolt M8 x 20 (28) with washer into the two front holes
and fasten them hand-tight (fig. D3).
• Tilt the table to a 45° angle.
• Insert one hex bolt M8 x 20 (28) with washer into the two rear holes
(fig. D4).
• Tighten all four bolts using the box spanner.
• Press the table insert (4) into place (fig. D5).
• Swing the connecting plate (26) back into place (fig. D1).
• Completely raise the blade guard (3) by turning the height adjuster (11)
clockwise (fig. A).
• Use a set square to check that the table is at a right angle to the saw
blade when in the horizontal position. If adjustment is needed, loosen
the table tilt locking lever and adjust the grub screw (29) as required
(fig. D6).
Mounting a blade (fig. A, D1, D5, E1 - E4)
The teeth of a new blade are very sharp and can be
dangerous.
• Unscrew the two retention knobs (8) and open the hinged cover (5) (fig. A).
• Swing back the connecting plate (26) which covers the blade slot in the
table (fig. D1).
• Remove the table insert (4).
• Guide the blade though the blade slot in the table. Make sure that the
teeth point to the front of the machine and downwards in the working
area (fig. E2).
• Carefully insert the blade into the blade guard slot (30) while turning it
90° (fig. E3 & E4).
• Position the blade between the guide blocks (19) and (21).
• Move the blade around the band wheels (31) and (32) (fig. E2).
If necessary, lower the upper band wheel by turning the blade tension
adjuster (6 in fig. A) counterclockwise.
• Mount the table insert (4) (fig. D5).
• Swing the connecting plate (26) back into place (fig. D1).
• Adjust the blade tension, the guide blocks and the support bearings as
described below.
Adjusting the blade tension (fig. F1)
The correct tension depends on the width of the blade used. Refer to the
table on the machine.
• Adjust the blade tension using the blade tension adjuster (6) until the
scale indicates the tension corresponding to the blade width.
Adjusting the blade position (fig. A, F2 & F3)
The blade must be centred on the rim of the band wheels.
• Open the hinged cover as described above.
• While rotating the upper band wheel with one hand, slightly rotate the
bladecentring adjuster (7) with the other (fig. A & F3).
Do not touch the blade but rotate the upper band wheel with
your finger on one of the spokes.
Adjusting the blade guide blocks and rear support bearings
(fig. B, G1 - G3)
During the sawing operation, the blade is exposed to frontal and lateral
forces. The rear support bearings (17 in fig. G1) are positioned 0.5 mm
behind the blade to control the blade front-to-back movement.
The 45° and 90° guide blocks are positioned 0.1 mm from the blade to
control the lateral blade position.
• Remove the table insert and tilt the table to 45°.
• Slacken the grub screws (18) and position the rear support bearings
(17) away from the blade (fig. G1).
• Adjust the knurled knob (33) to position the blade guide blocks just
behind the blade teeth (fig. G1).
14
All manuals and user guides at all-guides.com
• Position the rear support bearings (17) 0.1 mm behind the blade and
• Slacken the grub screws (20) and (22) and insert the blade guide
• Set the guide blocks to a distance of approx. 0.5 mm from the blade.
• Tighten the grub screws (20) and (22) (fig. G1).
Changing speed
DW738 (fig. H1 - H3)
Your DW738 bandsaw has two speeds. The low speed is obtained with
the drive belt on the small drive pulley (34) (fig. H2). The high speed is
obtained with the drive belt on the large drive pulley (35) (fig. H2).
For speed rates, refer to the technical data.
• Slacken the motor location bolt (13) and move the motor to relax the
• Ease the drive belt from the wheel pulley and subsequently from the
• Reinstall the drive belt on the wheel pulley and the required drive pulley (34)
• Reposition the motor to obtain the correct drive belt tension and
DW739 (fig. A & J)
The speed of your DW739 bandsaw is infinitely variable over a wide range
(refer to the technical data).
• With the motor running, turn the blade speed adjuster (14) to obtain the
Mounting and adjusting the rip fence (fig. A, K1 - K5)
• Mount a fence clamp piece (36 in fig. K1) on each end of the fence
• Put a D6 washer on each of the bolts and screw the plastic knobs (38)
• Slide the fence onto the table as shown (fig. K4). Make sure that the
• To set the fence, slacken the knobs (38) and slide the fence into the
• Secure the fence in position by first tightening the front knob, then the
Instructions for use
The attention of UK users is drawn to the "woodworking machines
regulations 1974" and any subsequent amendments.
Switching ON and OFF (fig. E1)
For reasons of security, the ON/OFF-switch (1) works only with the safety
key (2) inserted. It also offers a no-volt release function: should the power
be shut off for some reason, the switch has to be deliberately reactivated.
To operate:
• I = ON
• 0 = OFF
tighten the grub screws (18) (fig. G1).
blocks (19) and (21) in the holders (fig. G1).
drive belt (fig. H1).
drive pulley (34) or (35) (fig. H3).
or (35).
secure the motor location bolt (13) (fig. H1).
desired speed (fig. A2).
Do not force the speed adjuster beyond its range.
(10 in fig. A) using the M6 x 65 bolts (37 in fig. K1) as shown (fig. K1 & K2).
onto the bolts (fig. K3).
V-shaped lug (39) engages in the groove in the table (fig. K5).
desired position using the scale on the table (fig. K3).
rear knob. This ensures that the fence is aligned with the blade.
• Always observe the safety instructions and applicable
regulations.
• Do not force the cutting action. Allow the motor to reach full
speed before cutting.
• Select an appropriate saw blade.
• Never run the machine without the guards in place.
• Do not overtension the blade.
The tool now works in continuous operation.
E N G L I S H
en - 4