DeWalt DW738 Mode D'emploi page 19

6 Store idle tools
When not in use, Power Tools must be stored in a dry place and
locked up securely, out of reach of children.
7 Dress properly
Do not wear loose clothing or jewellery. They can be caught in moving
parts. Preferably wear rubber gloves and non-slip footwear when
working outdoors. Wear protective hair covering to keep long hair out
of the way.
8 Wear safety goggles
Also use a face or dust mask in case the operations produce dust or
flying particles.
9 Beware of maximum sound pressure
Take appropriate measures for the protection of hearing if the sound
pressure of 85 dB(A) is exceeded.
10 Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it frees both
hands to operate the tool.
11 Do not overreach
Keep proper footing and balance at all times.
12 Avoid unintentional starting
Do not carry the plugged-in tool with a finger on the switch.
Be sure that the switch is released when plugging in.
13 Stay alert
Watch what you are doing. Use common sense. Do not operate the
tool when you are tired.
14 Disconnect tool
Shut off power and wait for the tool to come to a complete standstill
before leaving it unattended. Unplug the tool when not in use, before
servicing or changing accessories.
15 Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed from the
tool before operating the tool.
16 Use appropriate tool
The intended use is described in this instruction manual. Do not force
small tools or attachments to do the job of a heavy-duty tool. The tool
will do the job better and safer at the rate for which it was intended.
Warning! The use of any accessory or attachment or performance of
any operation with this tool, other than those recommended in this
instruction manual may present a risk of personal injury.
17 Do not abuse cord
Never carry the tool by its cord or pull it to disconnect from the socket.
Keep the cord away from heat, oil and sharp edges.
18 Maintain tools with care
Keep the tools in good condition and clean for better and safer
performance. Follow the instructions for maintenance and changing
accessories. Inspect the tool cords at regular intervals and,
if damaged, have them repaired by an authorized D
agent. Inspect the extension cords periodically and replace them if
damaged. Keep all controls dry, clean and free from oil and grease.
19 Check for damaged parts
Before using the tool, carefully check it for damage to ensure that it will
operate properly and perform its intended function. Check for
misalignment and seizure of moving parts, breakage of parts and any
other conditions that may affect its operation. Have damaged guards
orother defective parts repaired or replaced as instructed.
Do not use the tool if the switch is defective. Have the switch replaced
by an authorized D WALT repair agent.
E
20 Have your tool repaired by an authorized D
This Power Tool is in accordance with the relevant safety regulations.
To avoid danger, electric appliances must only be repaired by qualified
technicians.
12
All manuals and user guides at all-guides.com
Additional safety instructions for bandsaws
• It is advisable to wear safety goggles when operating.
• Keep the upper blade guard as close to the workpiece as possible.
• When not in use, protect the saw blade completely using the blade guard.
• When not in use, when changing blades or carrying out maintenance,
• Before switching ON, make sure that the worktable is secured at the
• Always use sharp blades of the correct type designed for the
• Keep your hands well clear off the blade. Use a push stick for narrow
• Always make sure that the table insert is properly located. Replace the
• Never run the machine without all guards in place and the door locked.
• When working under abnormal conditions (exceptionally low
• When the machine is not going to be used for a prolonged period of
• Always secure round workpieces.
• Make sure that the blade rotates in the correct direction and that the
Residual risks
The following risks are inherent to the use of these saws:
- injuries caused by touching the rotating parts
- injuries caused by disruption of the saw blade
These risks are most evident:
- within the range of operation
- within the range of the rotating machine parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
These are:
- Impairment of hearing.
- Risk of accidents caused by the uncovered parts of the rotating saw
- Risk of injury when changing the blade.
- Risk of squeezing fingers when opening the guards.
- Health hazards caused by breathing dust developed when sawing
WALT repair
E
Package contents
The package contains:
1 Partly assembled machine
1 Table
1 Rip fence
1 Box spanner 8 mm
1 Pack containing:
WALT repair agent
E
disconnect the machine from the power supply.
required angle.
workpiece.
workpieces.
insert immediately when worn.
temperatures, lower mains supply voltage than normal or following a
long period of inactivity) the machine may have a tendency to stick.
In such a case, slacken the blade tension to approx. 100 N, switch the
motor ON and (while the motor is running) gradually increase the
tension to (50 x b) N, where b is the width of the saw blade in mm.
time, slacken the tensioner completely to eliminate the risk of blade
wheel distortion and resulting imbalance.
teeth are pointing downwards.
blade.
wood, especially oak and beech.
1 Table insert
2 Blade guide blocks 45°
2 Blade guide blocks 90°
3 Coach bolts M8 x 60
4 Hex nuts M8
8 Washers D8
2 Washers D6
1 Hex bolt M8 x 60
4 Hex bolts M8 x 20
2 Hex bolts M6 x 65
E N G L I S H
en - 2