Publicité
Les langues disponibles
Les langues disponibles
E N G L I S H
2 Knobs
2 Fence clamp pieces
1 Allen key 2.5 mm
1 Allen key 6 mm
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
Description
Your bandsaw DW738/DW739 has been designed for professional
workshop applications: it performs straight, circular, mitre and bevel cuts.
It can cut a wide range of materials such as wood, plastics, non-ferrous
metals and leather.
Fig. A
1 ON/OFF-switch
2 Safety key
3 Blade guard
4 Table insert
5 Hinged cover
6 Blade tension adjuster
7 Blade centring adjuster
8 Cover retention knobs
9 Table tilt locking lever
10 Fence
11 Blade guard height adjuster
12 Upper blade guard/guide assembly
13 Motor location bolt
14 Blade speed adjuster (DW739)
15 Table
16 Mounting holes
Fig. B
17 Rear blade support bearing
18 Locking grub screw for (17)
19 Blade guide blocks 45°
20 Locking grub screw for (19)
21 Blade guide blocks 90°
22 Locking grub screw for (21)
Optional accessories
Fig. C1
23 Legstand
Fig. C2
24 Mitre fence
25 Cut length gauge
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Mains plug replacement (U.K. & Ireland only)
• Should your mains plug need replacing and you are competent to do
this, proceed as instructed below. If you are in doubt, contact an
authorized D
WALT repair agent or a qualified electrician.
E
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
en - 3
All manuals and user guides at all-guides.com
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly
• The cable wire colours, or a letter, will be marked at the connection
• Before replacing the top cover of the mains plug ensure that the cable
For 115 V units with a power rating exceeding 1500 W, we recommend to
fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved extension cable suitable
for the power input of this machine (see technical data). The minimum
conductor size is 1.5 mm
When using a cable reel, always unwind the cable completely.
Also refer to the table below.
Conductor size (mm
0.75
1.00
1.50
2.50
4.00
Voltage
230
Assembly and adjustment
• The machine is fully assembled except for the table and rip fence.
Mounting the table (fig. A, D1 - D6)
• Turn the table tilt locking lever (9 in fig. A) counterclockwise
• Swing back the connecting plate (26) which covers the blade slot in the
• Place the table onto the segments (27) with the blade slot pointing to
• Carefully guide the table along the saw blade and align the holes in the
rated fuse (1).
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2) and Blue is for
Neutral (N) (4).
restraint (3) is holding the outer sheath of the cable firmly and that the
two leads are correctly fixed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N) wires to the earth pin
marked E or
.
2
.
2
)
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
Amperes
Cable rating (Amperes)
0
-
2.0
6
6
2.1
-
3.4
6
6
3.5
-
5.0
6
6
5.1
-
7.0
10
10
7.1
- 12.0
15
15
12.1 - 20.0
20
20
Prior to assembly and adjustment always unplug the tool.
approximately half a turn to release the tilt segments (27 in fig. D2).
table (fig. D1).
the front of the machine (fig. D2).
table with those in the segments.
30
45
60
6
6
6
6
6
6
6
6
6
6
10
15
10
10
15
15
15
15
20
20
20
20
25
-
13
Publicité
