Adding Gasoline To The Fuel Tank - Ryobi 3200 PSI Manuel D'utilisation

ETHANOL-BLENDED FUELS
NOTICE:
Do not use E15 or E85 fuel in this product. It is a viola-
tion of federal law and will damage the unit and void
your warranty. Only use unleaded gasoline containing
up to 10% ethanol.

ADDING GASOLINE TO THE FUEL TANK

See Figures 11-12.
DANGER:
Risk of fire and serious burns: Never remove fuel cap
when unit is running. Shut off engine and allow the unit
to cool at least five minutes. Remove cap slowly.
WARNING:
Gasoline and its vapors are highly flammable and ex-
plosive. To prevent serious personal injury and property
damage, handle gasoline with care. Keep away from igni-
tion sources, handle outdoors only, do not smoke while
adding fuel, and wipe up spills immediately.
WARNING:
Always shut off engine before fueling. Never remove
fuel cap or add fuel to a machine with a running or hot
engine. Make sure the unit is sitting on a flat, level sur-
face and only add fuel outdoors. If the engine is hot, let
the unit cool for at least five minutes before adding fuel.
After fueling, immediately replace fuel cap and tighten
securely. Move at least 30 ft. from refueling site before
starting engine. Do not smoke and stay away from open
flames and sparks! Failure to follow these instructions
could result in a fire and cause serious personal injury.
WARNING:
Check for fuel leaks. A leaking fuel cap, tank, or line is a
fire hazard and must be replaced immediately. If you find
any leaks, correct the problem before using the product.
Failure to do so could result in a fire that could cause
serious personal injury.
NOTE: This is a 4-cycle engine. DO NOT mix fuel and
lubricant together.
 Move the fuel valve to the CLOSED position.
 Mix fuel stabilizer with gasoline according to fuel stabilizer
manufacturer's directions.
 Before removing the fuel cap, clean the area around it.
Remove the fuel cap.
OPERATION
 Insert a clean funnel into the fuel tank then slowly pour
gasoline into the tank. Fill tank to approximately 1-1/2 in.
below the top of the tank neck (this allows for fuel
expansion).
 Replace fuel cap and tighten securely.
 Clean up any spills before starting the engine.
STARTING AND STOPPING THE PRESSURE
WASHER
See Figures 12 - 14.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
Before starting the engine:
 Connect all hoses.
NOTE: Make sure the pressure washer's water intake
screen is in place and unclogged before connecting
garden hose.
 Check all fluids (lubricant and gas).
 Turn on the garden hose then squeeze the trigger for 30
seconds to relieve air pressure; hold the trigger until a
steady stream of water appears.
NOTE: Make sure the faucet is turned on fully and that
there are no kinks or leaks in the hose.
To start the engine:
 Open the fuel valve.
 Move the choke lever to the START position.
NOTE: If restarting after a brief stop (i.e., after refueling
or moving), leave the choke lever in the RUN position.
 Grasp the starter grip and pull slowly until resistance is
felt. Give the starter grip a short, brisk pull to start the
engine.
NOTE: Do not allow the starter grip and rope to snap
back after starting; return it gently to its original place.
NOTICE:
If the starter grip and rope becomes difficult to pull,
squeeze the trigger to relieve water pressure before at-
tempting to start the engine again.
 Allow the engine to run for 5 seconds, then push the
choke to the RUN position.
10 — English