CAME SALOON Manuel D'installation page 30

• Employ this product only for the use for which it was expressly made.
Any other use is dangerous. CAME S.p.A is not liable for any damage
caused by improper, wrongful and unreasonable use • The safety of
this product and its proper fi tting depends, therefore, on respecting its
technical characteristics and proper fi tting, to be done in state-of-the-art
fashion, and under safe conditions as expressly explained in the literature
that comes with the product. • Keep these warnings together with the
installation and operation manuals that come with the operator.
Before installing
(checking what's there: if something is missing, do not continue until you
have complied with all safety provisions)
• Fitting and testing must be be only performed by qualifi ed technicians.
Laying the cables, installation and testing mus follow state-of-the-art pro-
cedures as dictated by regulations • Before beginning any operation it
is mandatory to carefully read all instruction; improper installation may
result in serious harm to people and things. • Make sure the operator is
in good mechanical state, balanced and aligned, and that it opens and
closes properly. Also, if needed, fi t suitable protections o use proper safety
sensors • If the operator is to be installed at a height of over 2.5 m from
the ground or other access level, make sure you have any necessary pro-
tections and/or warnings in place • Make sure that the opening turnstile
or gate cannot entrap people • Do not install the operator upside down
or onto elements that could yield and bend. If necessary, add suitable
reinforcements to the anchoring points • Do not install the operator on
tilted surfaces • Make sure any sprinkler systems cannot wet the operator
from the ground up.
• Suitably section off and demarcate the entire installation site to prevent
unauthorized persons from entering the area, especially minors and chil-
dren • Be careful when handling operators that weigh over 20 kg. If need
be, use proper safety hoisting equipment • The CE-marked safety devices
(photocells, stepping plates, sensitive safety-edges, emergency buttons,
and so on), must be fi tted in compliance with the regulations in eff ect and
according to state-of-the-art criteria, taking into account the environment,
the type of required service and of the working forces applied to moving
leaves. Any shearing or conveying points must be sensor-protected • Any
residual risks must be pointed out to end users and highlighted with pic-
tograms as provided by the law. • All opening commands (that is, buttons,
key switches, magnetic readers, and so on) must be installed at least 1.85
m from the perimeter of the gate's working area, or where they cannot
be reached from outside the gate. Also, any direct commands (buttons,
touch panels, and so on) must be installed at least 1.5 m from the ground
and must not be reachable by unauthorized persons • The turnstile must
visibly show its identifi cation data. • Before connecting the main power
supply make sure that the identifi cation data correspond to the those of
the network • The turnstile must be connected to an eff ective regulation
grounding system.
• The manufacturer declines any liability for using non-original products;
which would result in warranty loss • All maintained action commands,
must be fi tted in places from which the moving gate leaves and transit and
driving areas are visible • Apply, if missing, a permanent sign showing the
position of the release device • Before delivering to the users, make sure
the system is EN 12453 and EN 12445 standard compliant (regarding
impact forces), and also make sure the system has been properly adjusted
and that any safety, protection and manual release devices are working
properly • Apply Warning Signs where necessary and in a visible place.
Special user-instructions and recommendations
• Keep turnstile operation areas clean and free of any obstructions. Make
sure the photocell's operating fi eld is clear of any obstructions • do not
allow children to play with fi xed commands, or to loiter in the turnstile's
maneuvering area. Keep any remote control transmitters or any other
command device away from children, to prevent the operator from being
accidentally activated • The apparatus may be used by children of eight
years and above and by physically, mentally and perceptively challenged
people, or even ones without any experience, provided this happens un-
der close supervision or once they have been properly instructed to use
the apparatus safely and to the potential hazards involved. Cleaning and
maintenance by users must not be done by children, unless properly su-
important safety instructions for people:
READ CAREFULLY!
Premise
Installing
WARNING!
pervised • Frequently check the system for any malfunctions or signs
of wear and tear or damage to the moving structures, to the component
parts, all anchoring points, including cables and any accessible connec-
tions. Keep any hinges, moving joints and friction points properly lubri-
cated • Perform functional checks on the photocells and sensitive safety
edges, every six months. Constantly clean the photocells' glass covers
using a slightly water-moistened cloth; do not use solvents or chemicals
that could damage the devices • If repairs or modifi cations are required
to the system, cut off the main power supply and do not use it until safety
conditions have been restored • Cut off the power supply before per-
forming any manual openings • If the power supply cable is damaged, it
must be replaced by the manufacturer or authorized technical assistance
service, or in any case, by similarly qualifi ed persons, to prevent any risk •
It is FORBIDDEN for users to perform any OPERATIONS THAT ARE NOT EX-
PRESSLY REQUIRED OF THEM AND WHICH ARE NOT LISTED in the manu-
als. For any repairs, modifi cations and adjustments and for extra-ordinary
maintenance, CALL TECHNICAL ASSISTANCE • Log the job and checks
into the periodic maintenance log.
• Keep away from hinges and mechanical moving parts • Do not enter
the operator's area of operation when it is moving • Do not counter the
operator's movement as this could result in dangerous situations • Always
pay special attention to any dangerous points, which have to be labeled
with specifi c pictograms and/or black and yellow stripes • When using
a selector switch or a command in maintained actions, keep checking
that there are no persons within the operating range of any moving parts,
until the command is released • The gate may move at any time and
without warning • Always cut off the power supply before performing any
maintenance or cleaning.
Danger of hand crushing
Danger! High voltage.
Emergency button
Further recommendations for all