Dust/Chip Extraction; Starting Operation - Bosch GSR 1000 Notice Originale

Cordless drill/driver
Capacity
Number of battery cells
Charger
Article number
Charging time
Battery charging voltage
Charge current
Protection class
A) Limited performance at temperatures <0 °C
Assembly
Before any work on the power tool (e.g. maintenance,
u
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the middle
position. There is risk of injury from unintentionally
pressing the on/off switch.
Charging the battery (see figure A)
Do not use any other charger. The supplied charger is
u
matched to the lithium-ion battery that is fitted in your
power tool.
Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the charger. Chargers marked 230 V can
also be operated at 220 V.
Note: The battery is supplied partially charged. To ensure
the maximum performance of the battery, use the charger to
fully charge the battery before first use.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the Electronic Cell Protection (ECP). When the battery is
discharged, the power tool is switched off by means of a pro-
tective circuit: The application tool stops moving.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
The charging process begins as soon as you have inserted
the mains plug for the charger into the mains socket and the
charging connector (7) into the port (3) on the bottom of the
handle.
The battery charge indicator (5) indicates the charging pro-
gress. The indicator flashes green during the charging pro-
cess. When the battery is fully charged, the battery charge
indicator (5) is continuously lit green.
During the charging process, the handle of the power tool
will become warm. This is normal. If you are not planning to
use the power tool again soon, disconnect the power ad-
aptor from the mains. The power tool cannot be used during
the charging process. It is not defective if it does not work
during the charging process. Follow the instructions on cor-
rect disposal.
Bosch Power Tools
Changing the tool (see figure B)
GSR 1000
Ah 1.5 Before any work on the power tool (e.g. maintenance,
u
tool change, etc.) as well as during transport and stor-
3
age, set the rotational direction switch to the middle
position. There is risk of injury from unintentionally
1 600 A02 04P
pressing the on/off switch.
h 1 The drill spindle is locked when the on/off switch (6) is not
pressed. This makes it possible to change the application
V 15
tool in the drill chuck quickly, conveniently and easily.
A 1.5
Open the keyless chuck (1) by turning it in the direction of
/ II
rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the sleeve of the keyless chuck (1) by turning
it by hand in the direction of rotation ➋ until it audibly clicks
into place. This will automatically lock the drill chuck.
The lock will disengage again if you turn the sleeve in the op-
posite direction to remove the tool.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation

Starting Operation

Setting the rotational direction (see figure C)
The rotational direction switch (2) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (6) is being pressed.
Right rotation: To drill and to drive in screws, press the ro-
tational direction switch (2) through to the left stop.
Left Rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (2) through to the right
stop.
Switching on/off
To start the power tool, press and hold the on/off switch
(6).
The lamp (4) lights up when the on/off switch (6) is lightly or
fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
To switch off the power tool, release the on/off switch (6).
English | 9
1 609 92A 5J4 | (14.02.2020)